Extend Your Wi-Fi 6 Coverage to Every Corner of Your HomeThe TP-Link RE605X is an AX1800 Wi-Fi 6 range extender that boosts your existing wireless network to eliminate dead zones and weak signal areas. With combined speeds of up to 1800Mbps across dual bands, a built-in Gigabit Ethernet port, and support for MU-MIMO and OFDMA, it delivers faster, more reliable Wi-Fi to more devices — even in busy households. Compatible with any Wi-Fi router or access point.Key Features Wi-Fi 6 (802.11ax) — next-generation wireless technology for faster speeds and better performance in congested environments AX1800 Dual-Band Speeds — 574Mbps on 2.4GHz and 1201Mbps on 5GHz for a combined 1800Mbps 1× Gigabit Ethernet Port — connect a wired device such as a smart TV, gaming console, or NVR directly to the extender MU-MIMO and OFDMA — simultaneously serves multiple devices with less congestion and lower latency 2× External Antennas — improved signal strength and coverage compared to internal antenna designs Works with Any Router — compatible with all Wi-Fi routers and access points regardless of brand WPS One-Touch Setup — connect to your existing network in seconds with a single button press Access Point Mode — use as a standalone access point when connected via Ethernet for wired-to-wireless coverage Typical Use Cases Eliminating Wi-Fi dead zones in bedrooms, garages, or back gardens Extending Wi-Fi coverage in multi-storey homes where the router signal doesn’t reach Adding a wired Ethernet connection in a room without a wall socket via the Gigabit port Boosting Wi-Fi for smart home devices, IP cameras, or streaming devices in weak signal areas Temporary Wi-Fi extension for renovations, events, or pop-up setups Technical Specifications Specification Detail Model RE605X Wi-Fi Standard Wi-Fi 6 (IEEE 802.11ax/ac/n/a — 5GHz; 802.11ax/n/b/g — 2.4GHz) Wi-Fi Speed AX1800: 574Mbps (2.4GHz) + 1201Mbps (5GHz) Antennas 2× External (2×2 MU-MIMO) Ethernet Port 1× Gigabit (10/100/1000Mbps) Operating Modes Range Extender, Access Point Security WPA/WPA2/WPA3, WPA2-Enterprise Buttons WPS, Reset Power Consumption 10W Dimensions (W×D×H) 73.7 × 45.7 × 124.5 mm Certifications CE, FCC, RoHS Warranty 3 Years Frequently Asked Questions Does the RE605X work with my existing router? Yes. The RE605X is compatible with any Wi-Fi router or access point regardless of brand. It connects to your existing network wirelessly and rebroadcasts the signal with the same or a new network name. Do I need a Wi-Fi 6 router to use the RE605X? No. The RE605X works with any Wi-Fi router, including older Wi-Fi 5 (AC) and Wi-Fi 4 (N) routers. However, to take full advantage of Wi-Fi 6 speeds and features, a Wi-Fi 6 router is recommended. Can I use the RE605X as an access point? Yes. When connected to a router or switch via the Gigabit Ethernet port, the RE605X can operate in Access Point mode, providing wireless coverage from a wired connection. Where is the best place to position the RE605X? For best results, place the RE605X halfway between your router and the area with weak signal — ideally where it can still receive a strong signal from the router (at least 2–3 bars). Avoid placing it behind large appliances or thick concrete walls. Does the RE605X support WPA3 security? Yes. The RE605X supports WPA3 encryption, providing the latest wireless security standard for compatible devices.

Read more less

TP-Link RE205 AC750 Wi-Fi Range Extender – Dual-Band 300Mbps + 433Mbps Overview The TP-Link RE205 is a compact plug-in Wi-Fi range extender that eliminates dead zones and extends your existing wireless network to hard-to-reach areas of your home or office. Delivering combined speeds of up to 750Mbps across dual-band 2.4GHz (300Mbps) and 5GHz (433Mbps), it works with any Wi-Fi router or wireless access point. An intelligent signal light guides you to the optimal placement location for the best possible coverage — no guesswork required. Key Features AC750 Dual-Band Wi-Fi – Combined speeds of up to 750Mbps across 2.4GHz (300Mbps) and 5GHz (433Mbps) bands for flexible, stable wireless extension. Eliminates Wi-Fi Dead Zones – Extends your existing router’s signal to bedrooms, garages, backyards, and other areas with weak or no coverage. Intelligent Signal Light – Built-in LED signal indicator shows the strength of the connection to your router, helping you find the optimal placement location for maximum coverage. Universal Router Compatibility – Works with any Wi-Fi router or wireless access point regardless of brand; no special configuration required. Compact Plug-In Design – Plugs directly into a standard power outlet; no cables or desk space required. Simple Setup – Quick setup via the Tether app or WPS button; up and running in minutes. Use Cases Extending Wi-Fi to bedrooms, bathrooms, or floors far from the router Boosting signal in garages, backyards, and outdoor entertaining areas Improving coverage in homes with thick walls or multiple storeys Extending an existing router’s range without replacing it Small offices needing basic wireless coverage extension Technical Specifications Specification Details Model RE205 Wi-Fi Standard AC750 Dual-Band (802.11ac) 2.4GHz Speed Up to 300Mbps 5GHz Speed Up to 433Mbps Combined Speed Up to 750Mbps Signal Indicator Intelligent LED Signal Light Router Compatibility Any Wi-Fi Router or Wireless Access Point Setup Method Tether App or WPS Button Form Factor Compact Plug-In (Wall Outlet) Vendor TP-Link Frequently Asked Questions Will the RE205 work with my existing router? Yes. The RE205 is compatible with any Wi-Fi router or wireless access point, regardless of brand. It supports both 2.4GHz and 5GHz networks and requires no special configuration on your existing router. What is the intelligent signal light for? The built-in LED signal indicator shows the strength of the RE205’s connection to your router in real time. A strong signal reading means you’ve found a good placement spot; a weak reading means you should move the extender closer to the router. This takes the guesswork out of finding the optimal location. Does the RE205 create a separate Wi-Fi network name? By default, the RE205 creates an extended network with a slightly different name (e.g. your existing network name + “_EXT”). You can manually set it to use the same network name as your router so devices connect seamlessly, though roaming between the router and extender is not as seamless as a full mesh system. What is the difference between a range extender and a mesh Wi-Fi system? A range extender like the RE205 rebroadcasts your existing router’s signal to extend coverage. It is a cost-effective solution for adding coverage to one or two areas. A mesh Wi-Fi system (such as the TP-Link Deco range) uses multiple units that work together as one unified network with seamless roaming. For whole-home coverage with seamless device handoff, a mesh system is the better choice; for extending coverage to a specific area, a range extender is simpler and more affordable. How do I set up the RE205? Plug the RE205 into a power outlet, then set it up using the TP-Link Tether app on your smartphone or press the WPS button on both the RE205 and your router to connect automatically. Most users are up and running in under five minutes. Placement Tip: For best performance, place the RE205 halfway between your router and the dead zone — close enough to receive a strong signal from the router, but far enough to extend coverage into the area you need. Use the intelligent signal light to confirm a good connection before finalising placement.

Read more less

Whole-Home Wi-Fi Coverage with AC2600 Speed and 4×4 MU-MIMO The TP-Link RE650 is a high-performance AC2600 dual-band Wi-Fi range extender designed to eliminate dead zones and extend reliable wireless coverage across large homes, offices, and commercial spaces. With four external antennas, 4×4 MU-MIMO, and beamforming technology, the RE650 delivers fast, stable Wi-Fi to multiple devices simultaneously — all the way to the edges of your property. Description Operating on both 2.4GHz (up to 800Mbps) and 5GHz (up to 1733Mbps) bands concurrently, the RE650 provides a combined throughput of up to 2600Mbps. Its intelligent signal light guides you to the optimal placement location for maximum coverage. A built-in Gigabit Ethernet port lets you hardwire smart TVs, gaming consoles, or desktop PCs for the fastest possible wired connection. The RE650 also supports Access Point mode, converting a wired network into a full Wi-Fi access point. Manage everything via the TP-Link Tether app on iOS or Android. Key Features AC2600 dual-band Wi-Fi: 800Mbps (2.4GHz) + 1733Mbps (5GHz) 4×4 MU-MIMO — simultaneously serves multiple devices at full speed Beamforming — focuses Wi-Fi signal directly at connected devices 4 fixed external antennas — extends coverage up to 14,000 sq ft 1 × Gigabit Ethernet port for wired device connections Intelligent signal light for optimal placement guidance Access Point mode — adds Wi-Fi to any wired network Range Extender mode — boosts existing router coverage TP-Link Tether app support (iOS & Android) Compatible with any Wi-Fi router or wireless access point WPS one-touch setup Use Cases Large homes and multi-storey residences — eliminate Wi-Fi dead zones across every room and floor Home offices — maintain fast, stable connections for video calls, cloud storage, and remote work Entertainment setups — hardwire smart TVs and gaming consoles via the Gigabit port for lag-free streaming and gaming Small businesses and retail — extend Wi-Fi coverage across shopfronts, warehouses, or open-plan offices Wired-to-wireless conversion — use AP mode to add Wi-Fi capability to any Ethernet-connected network Security and surveillance — extend wireless coverage to reach IP cameras in hard-to-reach areas Specifications Specification Detail Model RE650 Wi-Fi Standard IEEE 802.11ac/n/g/b Wi-Fi Speed AC2600 (800Mbps @ 2.4GHz + 1733Mbps @ 5GHz) MIMO 4×4 MU-MIMO Antennas 4 × fixed external Coverage Up to 14,000 sq ft Ethernet Port 1 × 10/100/1000Mbps (RJ45) Wireless Modes Range Extender, Access Point Frequency Bands 2.4GHz & 5GHz (concurrent) Buttons WPS, Reset, LED, Power Power Consumption 12W (max) Dimensions 163 × 86 × 40 mm Weight 0.52g App Support TP-Link Tether (iOS & Android) SKU RE650 Barcode 6935364099411 Vendor TP-Link Frequently Asked Questions Will the RE650 work with my existing router? Yes. The RE650 is compatible with any Wi-Fi router or wireless access point, regardless of brand. What is the difference between Range Extender mode and Access Point mode? In Range Extender mode, the RE650 picks up your existing Wi-Fi signal and rebroadcasts it to extend coverage. In Access Point mode, it connects via Ethernet to your router and creates a new wireless access point — ideal for adding Wi-Fi to a wired network. How do I find the best location to place the RE650? The RE650 has an intelligent signal light on the front panel that indicates the strength of the signal from your router. Place it where the light shows a strong signal for optimal performance. Does the RE650 support MU-MIMO? Yes. The RE650 supports 4×4 MU-MIMO, which allows it to communicate with multiple devices simultaneously rather than one at a time, improving overall network efficiency. Can I manage the RE650 from my phone? Yes. The TP-Link Tether app (available for iOS and Android) lets you set up and manage the RE650 from your smartphone or tablet. Does the Gigabit port support full 1Gbps speeds? Yes. The RE650 includes a 10/100/1000Mbps Gigabit Ethernet port for wired connections to devices such as smart TVs, gaming consoles, and desktop computers. Does CCTV Guru ship this product Australia-wide? Yes. The RE650 is stocked locally and ships Australia-wide.

Read more less

TP-Link RE450 – AC1750 Wi-Fi Range Extender with Gigabit Port The TP-Link RE450 eliminates Wi-Fi dead zones by connecting to your existing router wirelessly and rebroadcasting a stronger signal to areas it can’t reach on its own. With AC1750 dual band speeds (450Mbps on 2.4GHz + 1300Mbps on 5GHz), three adjustable external antennas, and a Gigabit Ethernet port for wired device bridging, it’s a capable range extender for homes, offices, and small commercial premises across Australia. Works with any Wi-Fi router or wireless access point. Key Features AC1750 Dual Band Wi-Fi: 450Mbps on 2.4GHz and 1300Mbps on 5GHz for a combined 1750Mbps — three times faster than standard 802.11n extenders. 3 Adjustable External Antennas: Directional antenna positioning allows you to optimise coverage for your specific layout, reducing interference and improving signal reliability. Gigabit Ethernet Port: Converts the extender into a wireless bridge — connect a smart TV, gaming console, NVR, Blu-ray player, or desktop PC to your Wi-Fi network via a wired Gigabit connection. Intelligent Signal Light: LED indicator shows signal strength from the host router to help you find the optimal placement location for maximum coverage. Works with Any Router: Compatible with any 802.11a/b/g/n/ac Wi-Fi router or wireless access point regardless of brand. Australian Plug Type: Supplied with AU-standard plug for direct compatibility with Australian power outlets. RE Button: One-press WPS-style pairing with compatible routers for quick setup without accessing the web interface. Dual Band Flexibility: Extend either the 2.4GHz or 5GHz band, or both simultaneously, depending on your network requirements. Ideal Use Cases Extending Wi-Fi coverage to rooms, floors, or areas of a home or office where the router signal is weak or absent. Bridging a wired device (smart TV, NVR, gaming console) to a Wi-Fi network via the Gigabit Ethernet port without running new cable to the router. Improving Wi-Fi coverage in multi-storey homes, large open-plan offices, or buildings with thick walls. Providing reliable wireless connectivity to IP cameras or access control devices in areas with marginal router signal. Temporary Wi-Fi extension for short-term installations or rental properties where infrastructure changes are not possible. Technical Specifications Specification Detail Model RE450 Wi-Fi Standard IEEE 802.11ac/n/g/b Wi-Fi Speed (5GHz) Up to 1300Mbps (802.11ac) Wi-Fi Speed (2.4GHz) Up to 450Mbps (802.11n) Combined Speed AC1750 (1300 + 450Mbps) Antennas 3 × External Adjustable Ethernet Port 1 × 10/100/1000Mbps (Gigabit RJ45) Plug Type AU (Australian standard) Power Consumption 9W (max) Buttons RE (Range Extender), Reset, LED, Power Router Compatibility Works with any 802.11a/b/g/n/ac Wi-Fi router Dimensions 163 × 76.4 × 66.5 mm Weight 0.34kg SKU RE450 Barcode (EAN) 6935364095994 What’s in the Box 1 × RE450 AC1750 Wi-Fi Range Extender 1 × RJ45 Ethernet Cable Quick Installation Guide Frequently Asked Questions Will the RE450 work with my existing router? Yes. The RE450 is compatible with any 802.11a/b/g/n/ac Wi-Fi router or wireless access point, regardless of brand. It connects to your existing network wirelessly and rebroadcasts the signal. How do I find the best location to place the RE450? The built-in intelligent signal LED indicates the signal strength received from your router. Place the RE450 where the LED shows a strong signal — typically halfway between your router and the dead zone — for the best balance of coverage extension and speed. Can I connect a wired device to the RE450? Yes. The Gigabit Ethernet port allows you to connect a wired device — such as a smart TV, NVR, gaming console, or desktop PC — to your Wi-Fi network at Gigabit speeds, effectively turning the RE450 into a wireless bridge. Does the RE450 create a separate Wi-Fi network name (SSID)? By default, the RE450 can extend your existing network using the same SSID, allowing devices to roam between the router and extender seamlessly. It can also be configured with a separate SSID if preferred. Will using a range extender reduce my Wi-Fi speed? Range extenders that use a single radio to receive and retransmit on the same band can reduce throughput by up to 50%. The RE450 uses dual band Wi-Fi, which allows it to communicate with the router on one band while serving clients on the other, reducing this speed penalty for dual-band capable devices. Is the RE450 suitable for extending Wi-Fi to IP cameras? Yes. The RE450 can extend Wi-Fi coverage to areas where IP cameras are installed but router signal is insufficient. For cameras requiring a wired connection, the Gigabit Ethernet port can also be used to bridge a single camera or a small switch to the extended network. Does it plug directly into a wall socket? Yes. The RE450 plugs directly into a standard Australian power outlet (AU plug type included) — no separate power adapter or cable is required for power.

Read more less

8-Port PoE+ Gigabit Switch with Smart Recovery and Extended Range The TP-Link TL-SG1210MP is a feature-rich unmanaged Gigabit desktop switch with eight PoE+ ports, a 123W total power budget, and a suite of intelligent modes that go well beyond a basic plug-and-play switch. With PoE Auto Recovery, Extend Mode for 250m cable runs, Isolation Mode for client traffic separation, and a combo SFP/RJ45 uplink port, it's purpose-built for professional CCTV installations, multi-AP Wi-Fi deployments, and small business networks across Australia. Key Features 8× PoE+ Ports (802.3af/at): Power IP cameras, access points, VoIP phones, and other PoE/PoE+ devices at up to 30W per port via a single Ethernet cable. 123W Total PoE Budget: Generous shared power budget supports a full deployment of 8 standard PoE cameras or a mixed load of PoE+ devices. PoE Auto Recovery: Automatically detects and reboots unresponsive PoE-powered devices — ideal for IP cameras and access points that occasionally freeze or drop offline. Extend Mode (up to 250m): Extends data and PoE power delivery up to 250m at 10Mbps on ports 1–4 — essential for cameras positioned far from the switch in large properties. Priority Mode (Ports 1–2): Prioritises traffic on ports 1 and 2 to guarantee consistent performance for latency-sensitive devices such as NVRs and IP cameras. Isolation Mode: One-click client traffic separation prevents devices on different ports from communicating with each other — improving security and network performance in shared environments. 1× Combo SFP/RJ45 Uplink Port: Connect to a fibre backbone or upstream Gigabit switch via SFP module or standard RJ45 — flexible uplink options for professional installations. 20 Gbps Switching Capacity: Non-blocking switching fabric handles simultaneous high-bandwidth video streams from all 8 cameras without bottlenecks. Fanless & Silent: Completely silent operation — suitable for offices, reception areas, and home installations where noise is a concern. Physical Security Lock: Kensington-style lock slot for securing the unit in shared or public spaces. Common Use Cases 8-camera IP CCTV systems for small businesses, retail stores, and warehouses Multi-access-point Wi-Fi deployments in offices, schools, and hospitality venues Long cable run installations using Extend Mode (up to 250m) for perimeter cameras Shared network environments requiring client isolation (e.g. guest Wi-Fi, retail kiosks) Fibre uplink to a core switch in multi-floor or multi-building installations Replacing multiple PoE injectors with a single, clean multi-port solution Technical Specifications Model TL-SG1210MP RJ45 Ports 9× 10/100/1000Mbps (Ports 1–8 are PoE+) Combo SFP/RJ45 Port 1× 1000Mbps (Port 10, uplink) PoE Standard IEEE 802.3af (PoE) / 802.3at (PoE+) PoE Ports 8× (Ports 1–8) Max PoE Per Port 30W (802.3at) Total PoE Budget 123W Switching Capacity 20 Gbps Packet Forwarding Rate 14.88 Mpps MAC Address Table 4K Jumbo Frame 16KB Transmission Method Store-and-Forward Extend Mode Range Up to 250m at 10Mbps (Ports 1–4) Priority Mode Ports 1–2 (high priority) Isolation Mode Yes (one-click client separation) PoE Auto Recovery Yes Fan Fanless (silent) Physical Security Lock Yes Power Supply External adapter — 53.5V DC / 2.43A Max Power Consumption 7.93W (no PD) / 141.40W (full PoE load) Dimensions (W × D × H) 209 × 126 × 26mm Operating Temperature 0°C to 40°C Frequently Asked Questions Is the TL-SG1210MP managed or unmanaged? It is an unmanaged switch. There is no web interface or software — modes (Extend, Priority, Isolation) are toggled via physical buttons on the unit. This makes it fast to deploy with no configuration required. What is PoE Auto Recovery and why does it matter? PoE Auto Recovery periodically checks whether connected PoE devices (such as IP cameras) are still responding. If a device becomes unresponsive, the switch automatically cuts and restores power to reboot it — eliminating the need to manually power-cycle cameras or access points on site. How does Extend Mode work? Pressing the Extend Mode button reduces port speed to 10Mbps on ports 1–4 and extends the maximum cable distance from 100m to 250m. This is particularly useful for IP cameras installed at the perimeter of a large property or car park where running power is impractical. What is Isolation Mode used for? Isolation Mode prevents devices connected to different ports from communicating directly with each other, while still allowing all devices to access the uplink (internet/NVR). It's useful in shared environments — such as retail stores, hotels, or apartment buildings — where you want to keep client devices separated for security. Can I use the SFP port with a fibre module? Yes. Port 10 is a combo SFP/RJ45 port that accepts a standard Gigabit SFP fibre module (single-mode or multi-mode, sold separately). This allows you to connect the switch to a fibre backbone or upstream switch over long distances where copper Ethernet is impractical. How does the TL-SG1210MP compare to the TL-SF1005P? The TL-SG1210MP offers significantly more: Gigabit speeds (vs 100Mbps), 8 PoE+ ports (vs 4 PoE ports), a higher 123W budget (vs 58W), PoE Auto Recovery, Isolation Mode, Extend Mode, and an SFP uplink port. It's the better choice for professional CCTV and business network installations.

Read more less

8-Port PoE+ Gigabit Easy Smart Switch with 123W Budget, SFP Uplink and PoE Auto Recovery The TP-Link TL-SG1210MPE is a 10-port Gigabit Easy Smart switch that combines eight 802.3at PoE+ ports, a 123W total power budget, a combo Gigabit SFP/RJ45 uplink port, and essential smart management features — including VLAN, QoS, IGMP Snooping, and PoE Auto Recovery — in a compact, fanless desktop form factor. With web-based management and the Easy Smart Configuration Utility, it's a capable, low-noise solution for small to medium CCTV installations, multi-AP Wi-Fi deployments, and business networks across Australia that need more than a basic unmanaged PoE switch. Key Features 8× PoE+ Ports (802.3af/at, Ports 1–8): Power IP cameras, wireless access points, VoIP phones, and other PoE/PoE+ devices at up to 30W per port via a single Ethernet cable. 123W Total PoE Budget: One of the highest PoE budgets in the Easy Smart category — supports a full mix of PoE and PoE+ devices simultaneously with significant headroom. 1× Combo Gigabit SFP/RJ45 Port (Port 10): Flexible uplink port accepts either a standard RJ45 Gigabit connection or a Gigabit SFP module for fibre uplinks to a core switch or NVR. PoE Auto Recovery: Automatically detects and restarts unresponsive PoE devices (such as frozen IP cameras) by cycling power — reducing the need for manual on-site intervention. VLAN Support (802.1Q, Port-based, MTU): Segment camera traffic, staff devices, and guest networks onto separate logical networks for improved security and performance. QoS (Port-based, 802.1p, DSCP): 4 priority queues with rate limiting and storm control — prioritises latency-sensitive traffic such as IP camera streams and VoIP calls. IGMP Snooping (V1/V2/V3): Optimises multicast traffic for IP camera streams and IPTV, reducing unnecessary bandwidth consumption across the network. Static Link Aggregation: Bond multiple ports for increased bandwidth and redundancy between the switch and an upstream device. Web-Based Management: Configure and monitor via a web browser or the Easy Smart Configuration Utility — no CLI or advanced networking knowledge required. Fanless & Silent: Completely silent operation — suitable for offices, reception areas, and home installations. 20 Gbps Switching Capacity: Non-blocking fabric handles simultaneous full-speed traffic across all 10 ports. Common Use Cases Small to medium CCTV installations with up to 8 IP cameras and PoE Auto Recovery for unattended reliability Multi-AP Wi-Fi deployments with VLAN separation between staff and guest networks Small business networks requiring both PoE+ and basic traffic management in one device VoIP phone deployments needing PoE+ power and QoS prioritisation for call quality Fibre uplink installations using the combo SFP port to connect to a fibre backbone switch Upgrading from an unmanaged PoE switch to gain VLAN, QoS, and PoE Auto Recovery Technical Specifications Model TL-SG1210MPE Total Ports 10 (9× Gigabit RJ45 + 1× Combo SFP/RJ45) PoE+ Ports 8× (Ports 1–8), IEEE 802.3af/at Max PoE Per Port 30W (802.3at) Total PoE Budget 123W Uplink Port 1× Combo Gigabit SFP/RJ45 (Port 10) Switching Capacity 20 Gbps Packet Forwarding Rate 14.88 Mpps MAC Address Table 4K Jumbo Frame 16KB QoS Port-based, 802.1p, DSCP — 4 priority queues, rate limiting, storm control VLAN 802.1Q Tag VLAN, Port-based VLAN, MTU VLAN IGMP Snooping V1/V2/V3 Link Aggregation Static Link Aggregation PoE Auto Recovery Yes Management Web UI, Easy Smart Configuration Utility Fan Fanless (silent) Power Supply External adapter — 53.5V DC / 2.43A Max Power Consumption 7.66W (no PD) / 141.54W (full PoE load) Dimensions (W × D × H) 209 × 126 × 26mm Frequently Asked Questions What is the difference between the TL-SG1210MPE and the TL-SG108PE? The TL-SG1210MPE has 10 ports (8 PoE+ + 1 RJ45 + 1 combo SFP/RJ45), a 123W PoE budget, PoE Auto Recovery, IGMP Snooping, Static Link Aggregation, and a 16KB jumbo frame. The TL-SG108PE has 8 ports (4 PoE + 4 standard RJ45), a 55W budget, and no SFP port or PoE Auto Recovery. Choose the TL-SG1210MPE for larger PoE deployments requiring more ports, higher power budget, fibre uplink capability, and PoE Auto Recovery. What is PoE Auto Recovery and why does it matter for CCTV? PoE Auto Recovery monitors connected PoE devices and automatically cycles power to any device that stops responding — effectively rebooting a frozen IP camera or access point without requiring a site visit. For unattended CCTV installations, this is a significant reliability feature that reduces maintenance callouts and ensures cameras stay online. Can I use the SFP port for a fibre uplink? Yes. Port 10 is a combo SFP/RJ45 port that accepts either a standard RJ45 Gigabit connection or a Gigabit SFP module for fibre uplinks. This allows the switch to connect to a fibre backbone switch or NVR over single-mode or multi-mode fibre — useful in installations where the switch is located far from the core network. How many PoE cameras can I connect and what is the power budget? Up to 8 IP cameras can be connected via the PoE+ ports (Ports 1–8). The total shared PoE budget is 123W. For example, 8 cameras drawing 15W each would use 120W — just within the 123W budget. For higher-power PTZ cameras or PoE+ APs, calculate your total load carefully to stay within budget. Is it managed or unmanaged? The TL-SG1210MPE is an Easy Smart switch — it provides a web-based management interface for configuring VLANs, QoS, IGMP Snooping, Link Aggregation, and PoE Auto Recovery without the complexity of a fully managed switch. It's ideal for installers and small business owners who need more control than an unmanaged switch but don't require enterprise-level CLI management. Does it work out of the box without configuration? Yes. The TL-SG1210MPE works as a standard plug-and-play switch out of the box — all devices connected will communicate normally without any setup. Smart features such as VLAN, QoS, and PoE Auto Recovery are only applied when you choose to configure them via the web interface.

Read more less

10 Gigabit SFP+ Managed Switching with Omada SDN for Demanding NetworksThe TP-Link TL-SX3008F is an 8-port 10 Gigabit SFP+ L2+ managed switch designed for high-performance network backbones, data centres, and enterprise edge deployments. With a 160 Gbps non-blocking switching capacity, fanless silent operation, and full Omada SDN integration, it delivers the speed, control, and reliability required by professional installers and network engineers.Key Features 8× 10GE SFP+ Slots — full 10 Gigabit fibre or DAC connectivity on every port 160 Gbps Switching Capacity — non-blocking performance at 119.04 Mpps forwarding rate Omada SDN Integration — Zero-Touch Provisioning, centralised cloud management, and intelligent monitoring Static Routing — inter-VLAN routing and basic L3 forwarding without a dedicated router L2/L3/L4 QoS — 8 priority queues with 802.1p CoS/DSCP, SP/WRR/SP+WRR scheduling for voice and video optimisation IGMP Snooping — efficient multicast traffic management for video surveillance and streaming Robust Security — ACL, Port Security, DoS Defence, Storm Control, DHCP Snooping, 802.1X, RADIUS authentication Link Aggregation — up to 8 LAG groups with static and 802.3ad LACP support Fanless Design — silent operation, suitable for noise-sensitive environments Standalone Management — Web GUI, CLI, SNMP, RMON, and Dual Image support Rack-Mountable — standard 1U 19-inch rack form factor Typical Use Cases 10G network backbone aggregation in enterprise and campus environments High-speed uplink for IP camera systems and NVR servers requiring 10G throughput Data centre top-of-rack switching with fibre or DAC cable connections Aggregation layer in multi-site Omada SDN deployments High-density server interconnect for virtualisation and storage networks Technical Specifications Specification Detail Model TL-SX3008F SFP+ Ports 8× 10GE SFP+ Console Ports 1× RJ45, 1× Micro-USB Switching Capacity 160 Gbps Packet Forwarding Rate 119.04 Mpps MAC Address Table 32K Jumbo Frame 9 KB QoS L2/L3/L4, 8 priority queues, 802.1p CoS/DSCP, SP/WRR/SP+WRR Link Aggregation Up to 8 groups, static + 802.3ad LACP Routing Static Routing, inter-VLAN routing Management Web GUI, CLI, SNMP v1/v2c/v3, RMON, Omada SDN, Dual Image Security ACL, Port Security, DoS Defence, Storm Control, DHCP Snooping, 802.1X, RADIUS Fan Fanless Power Supply 100–240V AC, 50/60Hz Max Power Consumption 15.46W Dimensions (W×D×H) 440 × 180 × 44 mm (1U rack) Mounting Rack-mountable (19-inch, 1U) Warranty 5 Years Frequently Asked Questions What type of transceivers are compatible with the TL-SX3008F? The TL-SX3008F uses standard SFP+ slots and is compatible with TP-Link SFP+ modules (including 10GBase-SR, 10GBase-LR, and 10GBase-ER transceivers) as well as DAC (Direct Attach Copper) cables. Third-party SFP+ modules may also work but are not officially supported. Does the TL-SX3008F support PoE? No. The TL-SX3008F is a fibre/SFP+ switch and does not support Power over Ethernet. For PoE switching, consider the TP-Link TL-SG3428MP or TL-SG2428P from the JetStream range. Can it be managed without an Omada controller? Yes. The TL-SX3008F supports standalone management via Web GUI, CLI (console or SSH), and SNMP. An Omada controller is optional and only required for centralised multi-device management. Is the TL-SX3008F suitable for IP camera backbone networks? Yes. Its 10G SFP+ uplinks, IGMP snooping, and L2/L3/L4 QoS make it well-suited as a backbone or aggregation switch in large IP camera installations where high-bandwidth video streams need to be prioritised. Does it support VLAN configuration? Yes. The TL-SX3008F supports 802.1Q VLAN, voice VLAN, and inter-VLAN routing via static routing, allowing network segmentation for security cameras, management traffic, and user networks on the same switch.

Read more less

TP-Link TL-SX1008 — 8-Port 10G Multi-Gigabit Unmanaged Switch The TP-Link TL-SX1008 delivers true 10 Gigabit connectivity across all 8 ports in a compact, plug-and-play package. Whether you’re building a high-speed NAS network, connecting 10G workstations, or upgrading a small server room, the TL-SX1008 provides 160 Gbps of non-blocking switching capacity with zero configuration required. Backwards compatible with existing Cat5e/Cat6 cabling at lower speeds, and rack or desktop mountable, it’s a straightforward 10G upgrade for Australian businesses, installers, and power users. Key Features 8× 10G Multi-Gigabit Ports: Each port auto-negotiates at 100 Mbps, 1 Gbps, 2.5 Gbps, 5 Gbps, or 10 Gbps — fully backwards compatible with existing Cat5e/Cat6 cabling. 160 Gbps Non-Blocking Switching: Full wire-speed performance across all 8 ports simultaneously, with a 119 Mpps forwarding rate and 10 KB jumbo frame support. Plug and Play: No configuration, no software, no management interface required — connect and go in seconds. Intelligent Fan Speed Adjustment: The single built-in fan automatically adjusts speed based on operating temperature, reducing noise during light workloads. Desktop & 1U Rack Mountable: Compact 1U form factor (294 × 180 × 44 mm) with included rackmount kit and rubber feet for flexible deployment. All-Metal Construction: Durable metal casing aids heat dissipation and long-term reliability in demanding environments. 802.1p/DSCP QoS: Basic traffic prioritisation ensures latency-sensitive applications like video and VoIP perform reliably. 802.3X Flow Control: Prevents packet loss during traffic bursts between connected devices. Use Cases NAS & Storage Networks: Maximise throughput between 10G NAS devices and workstations for fast file transfers, backups, and media streaming. Server Rooms & Small Data Centres: Connect multiple servers at 10G speeds without the overhead of a managed switch. High-Performance Workstations: Ideal for video editors, 3D rendering, and content creators who need fast local network transfers. Wi-Fi 6/6E Backhaul: Provide a 10G wired backbone for 2.5G, 5G, or 10G wireless access points to eliminate backhaul bottlenecks. LAN Gaming & Home Entertainment: Low-latency 10G connectivity for gaming rigs, 8K video streaming, and home media servers. Business Office Upgrades: Upgrade legacy Gigabit infrastructure to 10G without complex managed switch configuration. Specifications Model TL-SX1008 Ports 8 × 100M/1G/2.5G/5G/10G RJ45 (Auto-Negotiation, Auto-MDI/MDIX) Standards IEEE 802.3, 802.3u, 802.3ab, 802.3x, 802.1p, 802.3an, 802.3bz Switching Capacity 160 Gbps Forwarding Rate 119.0 Mpps MAC Address Table 32K entries Packet Buffer Memory 2 Mb Jumbo Frame 10 KB Transfer Method Store and Forward QoS 802.1p / DSCP Flow Control 802.3X Fan 1 × (intelligent speed adjustment) Power Supply 100–240V AC, 50/60 Hz, 0.8A Max Power Consumption 31.2W Dimensions (W × D × H) 294 × 180 × 44 mm Weight 2.1 kg Operating Temperature 0–50°C Operating Humidity 10–90% RH (non-condensing) Certifications CE, FCC, RoHS In the Box Switch, power cord, rackmount kit, rubber feet, installation guide Frequently Asked Questions Does the TL-SX1008 require any configuration or software? No. The TL-SX1008 is a fully unmanaged plug-and-play switch. Simply connect your devices and it works immediately — no web interface, no app, and no management software required. Is the TL-SX1008 backwards compatible with Gigabit devices? Yes. Each port auto-negotiates at 100 Mbps, 1 Gbps, 2.5 Gbps, 5 Gbps, or 10 Gbps, so you can mix legacy Gigabit devices with 10G devices on the same switch without any issues. What cabling does 10G require? For 10 Gbps speeds, Cat6A cabling is recommended for runs up to 100 metres. Cat6 can support 10G up to approximately 55 metres depending on cable quality and environment. Cat5e is not recommended for 10G. Can the TL-SX1008 be rack mounted? Yes. A rackmount kit is included in the box, allowing the switch to be installed in a standard 19-inch rack in a 1U slot. Rubber feet are also included for desktop use. How loud is the fan? The TL-SX1008 features intelligent fan speed adjustment — the fan runs slower and quieter during light workloads and ramps up only when temperatures rise. It is suitable for office environments but may not be ideal for silent home theatre setups under heavy load. Is the TL-SX1008 suitable for connecting to a 10G NAS? Yes. This is one of the most common use cases. The TL-SX1008 provides full 10G connectivity between a NAS and multiple workstations simultaneously, eliminating the Gigabit bottleneck for large file transfers, video editing, and backup workflows.

Read more less

TP-Link TL-SL1311MP 8-Port PoE+ Desktop Switch with Gigabit & SFP Uplinks 8-Port PoE+ Switch with Gigabit Uplinks & 250m Extend Mode The TP-Link TL-SL1311MP is a compact desktop PoE+ switch with 8 Fast Ethernet PoE+ ports, 2 Gigabit RJ45 uplinks, and 1 Gigabit SFP uplink — all in a fanless, plug-and-play form factor. With a 124 W total PoE budget, up to 30 W per port, Extend Mode for PoE transmission up to 250 m, and PoE Auto Recovery, it’s a practical and cost-effective solution for powering IP cameras, VoIP phones, and wireless access points in small Australian business and residential installations. Key Features 8 × 10/100 Mbps PoE+ ports — 802.3af/at compliant, up to 30 W per port 124 W total PoE budget across all 8 ports 2 × Gigabit RJ45 uplink ports + 1 × Gigabit SFP uplink port Extend Mode — extends PoE data and power transmission up to 250 m at 10 Mbps (ports 1–4 or 1–8) PoE Auto Recovery — automatically reboots unresponsive PoE devices without manual intervention Isolation Mode — one-click client traffic separation for improved security and performance Fanless design — silent operation, suitable for offices, reception areas, and noise-sensitive environments Plug-and-play — no configuration or software required Physical security lock — prevents unauthorised removal 7.6 Gbps switching capacity, 5.6544 Mpps forwarding rate 16 KB Jumbo Frame support Use Cases IP CCTV Systems: Power and connect up to 8 PoE IP cameras without separate power supplies. Use Extend Mode to push PoE up to 250 m for remote camera positions. Small Office Networks: Connect PoE VoIP phones and wireless access points while using the Gigabit uplinks to connect to a core switch or router. Wireless Access Points: Deploy PoE-powered APs throughout a small office or retail space without additional power cabling. Retail & Hospitality: Isolation Mode separates guest and staff device traffic on the same switch for improved security. Fibre Uplink Installations: The Gigabit SFP port allows connection to a fibre uplink or fibre-connected core switch for longer-distance backbone runs. Specifications Specification Detail Model TL-SL1311MP PoE Ports 8 × 10/100 Mbps RJ45 (802.3af/at PoE+) Uplink Ports 2 × Gigabit RJ45 + 1 × Gigabit SFP PoE Power Per Port Up to 30 W Total PoE Budget 124 W Extend Mode Up to 250 m @ 10 Mbps (ports 1–4 or 1–8) Switching Capacity 7.6 Gbps Packet Forwarding Rate 5.6544 Mpps MAC Address Table 2K Jumbo Frame 16 KB Transfer Method Store-and-Forward Power Supply External adapter — 53.5 V DC / 2.43 A Max Power Consumption 5.95 W (no PoE load) / 140.92 W (full 124 W PoE load) Cooling Fanless Dimensions (W × D × H) 209 × 126 × 26 mm Weight 1.56 kg Physical Security Lock Yes Frequently Asked Questions How many PoE cameras can I connect to the TL-SL1311MP? Up to 8 PoE-powered devices on ports 1–8. The total PoE budget is 124 W — if each camera draws 15 W, all 8 ports can run simultaneously. Higher-draw devices (e.g., PTZ cameras at 25–30 W) will reduce the number of simultaneous powered ports. Plan your PoE budget based on the actual wattage of your connected devices. What is Extend Mode and when should I use it? Extend Mode reduces port speed to 10 Mbps to extend PoE data and power transmission up to 250 m. It is useful for remote camera positions where the cable run exceeds the standard 100 m Ethernet limit. Activate it via the hardware button on the switch — it can be applied to ports 1–4 or ports 1–8. What is PoE Auto Recovery? PoE Auto Recovery monitors connected PoE devices and automatically power-cycles any device that becomes unresponsive — similar to unplugging and replugging the device. This is particularly useful for IP cameras or access points that may occasionally freeze or lock up, reducing the need for on-site intervention. What is Isolation Mode? Isolation Mode separates client traffic between PoE ports so that devices connected to different ports cannot communicate directly with each other — only with the uplink. This improves security in environments where you don’t want devices to see each other, such as guest Wi-Fi APs or public-facing kiosks. Can I use the SFP port for a fibre uplink? Yes. The Gigabit SFP port accepts standard SFP MSA-compliant transceivers, including TP-Link’s SM311LS (single-mode, 10 km) and compatible multi-mode modules, allowing you to connect the switch to a fibre-based core switch or backbone over longer distances.

Read more less

The TP-Link TL-SX105 is a flagship 5-port 10-Gigabit desktop switch designed to provide the ultimate bandwidth for power users, small offices, and home labs. With a massive 100Gbps switching capacity, this unmanaged switch delivers lightning-fast connections for 10G NAS, servers, WiFi 6 APs, and high-end workstations, eliminating network bottlenecks instantly. Key Features Full 10G Connectivity: Equipped with 5× 10-Gigabit ports that unlock the highest performance of your 10G/Multi-Gig bandwidth and devices. 100Gbps Switching Capacity: Provides non-blocking wire-speed forwarding for maximum throughput without congestion. Multi-Gigabit Compatibility: 5-speed (100M/1G/2.5G/5G/10G) auto-negotiation ports provide optimal performance for all your devices. Silent Operation: The revolutionary fanless design ensures quiet operation, making it ideal for noise-sensitive environments like home offices or recording studios. Durable Metal Casing: Rugged metal housing and professional heat dissipation design ensure a wide operating temperature range (0–40 ℃). Plug and Play: No configuration or software required—simply plug in your devices and enjoy instant 10-Gigabit speeds. Technical Specifications Standards and Protocols IEEE 802.3, 802.3u, 802.3ab, 802.3bz, 802.3an, 802.3x, 802.1p Interface 5× 100Mbps/1Gbps/2.5Gbps/5Gbps/10Gbps Ports Switching Capacity 100 Gbps Fan Quantity Fanless (Silent) External Power Supply External Power Adapter (12VDC / 2.0A) Dimensions (W x D x H) 226 × 131 × 35 mm Advanced Features 802.3X Flow Control, 802.1p/DSCP QoS More Information View Official TP-Link Product PageDownload Installation Guide & Datasheet Note: For 10Gbps speeds, please ensure you are using Category 6a (Cat6a) or higher Ethernet cabling.

Read more less

Gigabit Multi-WAN VPN Router with Omada SDN and Enterprise-Grade Security The TP-Link TL-ER7206 SafeStream is a Gigabit multi-WAN VPN router designed for small to medium businesses that require reliable internet connectivity, secure remote access, and centralised network management. With up to four WAN ports (including a Gigabit SFP WAN), support for 100 simultaneous IPsec VPN tunnels, and full integration with TP-Link's Omada SDN platform, it delivers enterprise-grade routing, security, and cloud management at an accessible price point — ideal for multi-site business networks, retail chains, and professional CCTV and IT installations across Australia. Key Features Up to 4 WAN Ports: 1× Gigabit SFP WAN, 1× Gigabit RJ45 WAN, and 2× configurable Gigabit WAN/LAN ports — enabling load balancing and failover across multiple ISP connections for maximum uptime. Highly Secure VPN: Supports up to 100× LAN-to-LAN IPsec, 50× OpenVPN, 50× L2TP, and 50× PPTP simultaneous VPN connections — ideal for secure remote access and site-to-site connectivity. Omada SDN Integration: Centrally manage alongside Omada switches and access points via cloud or local controller — with Zero-Touch Provisioning (ZTP) for rapid remote deployment across multiple sites. Centralised Cloud Management: Monitor and configure the router from anywhere via the Omada cloud platform or Omada app on iOS and Android. Advanced Firewall & Security: Comprehensive security suite including DoS defence, IP/MAC/URL filtering, advanced firewall policies, and access control to protect your network and data. Load Balancing & Failover: Distribute traffic across multiple WAN connections for optimised bandwidth usage, and automatically failover to a backup WAN if the primary connection drops. Gigabit SFP WAN Port: Supports fibre WAN connections via SFP module — ideal for NBN FTTP, fibre business internet, or fibre uplinks in multi-building deployments. 512MB DRAM & 128MB NAND Flash: Generous memory for handling high VPN tunnel counts and complex routing policies without performance degradation. Rack Mountable: Standard rack-mount form factor for professional installation in comms cabinets and server rooms. Common Use Cases Multi-WAN load balancing and failover for business-critical internet connectivity Site-to-site IPsec VPN between multiple business locations or branches Secure remote access VPN for staff working from home or on the road Multi-site retail and hospitality networks managed centrally via Omada cloud Professional CCTV and IT installations requiring secure remote management NBN fibre business internet connections via the Gigabit SFP WAN port Technical Specifications Model TL-ER7206 WAN Ports 1× Gigabit SFP WAN + 1× Gigabit RJ45 WAN + 2× Gigabit WAN/LAN (configurable) LAN Ports 2× Fixed Gigabit RJ45 LAN + 2× Configurable WAN/LAN Total Gigabit Ports 6 (1× SFP + 5× RJ45) VPN — IPsec Up to 100× LAN-to-LAN tunnels VPN — OpenVPN Up to 50× simultaneous connections VPN — L2TP Up to 50× simultaneous connections VPN — PPTP Up to 50× simultaneous connections Load Balancing Yes (multi-WAN) WAN Failover Yes (automatic) Firewall Advanced policies, DoS defence, IP/MAC/URL filtering, ACL SDN Management Omada SDN (cloud & local controller) Zero-Touch Provisioning Yes (ZTP via Omada) DRAM 512MB Flash SPI 4MB + NAND 128MB Protocols TCP/IP, DHCP, ICMP, NAT, PPPoE, SNTP, HTTP, DNS, IPsec, PPTP, L2TP Standards IEEE 802.3, 802.3u, 802.3ab Power Supply 100–240V AC, 50/60Hz (internal) Mounting Rack mountable Dimensions (W × D × H) 226 × 131 × 35mm Frequently Asked Questions What is multi-WAN load balancing and why does it matter? Multi-WAN load balancing distributes internet traffic across two or more WAN connections simultaneously — maximising total available bandwidth and preventing any single connection from becoming a bottleneck. For businesses with high internet usage or multiple users, this can significantly improve performance. Combined with automatic failover, if one WAN connection drops, traffic is automatically rerouted to the remaining connections with no manual intervention. What VPN protocols does the TL-ER7206 support? The TL-ER7206 supports IPsec (up to 100 LAN-to-LAN tunnels), OpenVPN (up to 50 connections), L2TP (up to 50 connections), and PPTP (up to 50 connections). IPsec is recommended for site-to-site VPN between business locations; OpenVPN is recommended for secure remote access by individual staff members. What is Omada SDN and do I need a controller? Omada SDN is TP-Link's centralised network management platform. The TL-ER7206 can be managed via the Omada cloud (no hardware controller required), a hardware Omada controller (OC300/OC200), or a software controller on a local server. Zero-Touch Provisioning (ZTP) allows the router to be pre-configured in the cloud and automatically download its configuration when connected on site — ideal for remote deployments. Can I use the SFP WAN port for an NBN fibre connection? Yes. The Gigabit SFP WAN port accepts a standard Gigabit SFP module (sold separately) for fibre WAN connections — compatible with NBN FTTP connections and fibre business internet services. Use a single-mode or multi-mode SFP module appropriate for your fibre infrastructure. How many devices can connect to the TL-ER7206? The TL-ER7206 is a router, not a switch — it manages routing and WAN connectivity. Connect it to a TP-Link Omada switch (such as the TL-SG2428P or TL-SG3428XMP) to provide wired ports for client devices, and to Omada access points for wireless coverage. The router itself handles the routing and VPN functions for the entire network. Is it suitable for a CCTV installation? Yes. The TL-ER7206 is an excellent choice as the gateway router in a professional CCTV installation — providing secure remote access to NVRs and cameras via VPN, multi-WAN failover for continuous connectivity, and Omada SDN integration for centralised management alongside VIGI cameras and VIGI NVRs.

Read more less

16-Port Gigabit PoE+ Rackmount Switch for Professional Surveillance and Business Networks The TP-Link TL-SG1218MP is a plug-and-play unmanaged rackmount switch with 16 Gigabit PoE+ ports, a 250W total power budget, and two combo Gigabit SFP slots — all housed in a durable metal chassis rated for operating temperatures up to 50°C. Designed for professional CCTV installations, multi-AP Wi-Fi deployments, and small to medium business networks, it delivers high-power PoE+ performance in a clean 1U rack form factor without the complexity of managed switch configuration. Key Features 16× Gigabit PoE+ Ports (802.3at/af): Power and connect IP cameras, wireless access points, VoIP phones, and other PoE/PoE+ devices at up to 30W per port across all 16 ports. 250W Total PoE Budget: High shared power budget supports a full deployment of 16 standard PoE cameras or a mixed load of PoE+ devices — one of the highest budgets available in an unmanaged switch. 2× Non-PoE Gigabit RJ45 Ports: Dedicated uplink ports for connecting to a router, NVR, or upstream switch via copper Ethernet. 2× Combo Gigabit SFP Slots: Flexible fibre or copper uplink options — connect to a fibre backbone or upstream switch using SFP modules (single-mode or multi-mode) or standard RJ45 cables. 802.1p/DSCP QoS: Prioritises latency-sensitive traffic such as IP camera streams and VoIP calls to ensure consistent performance under heavy network load. Plug & Play: No configuration, software, or management interface required — connect devices and the switch operates automatically. Durable Metal Chassis: Robust metal casing with professional heat dissipation design supports an operating temperature range of 0–50°C — suitable for comms cabinets and server rooms without air conditioning. 36 Gbps Switching Capacity: Non-blocking switching fabric handles simultaneous high-bandwidth video streams from all 16 cameras without bottlenecks. Rack Mountable (1U): Standard 19-inch rack form factor (440 × 180 × 44mm) for clean, professional installations in comms cabinets and equipment racks. Physical Security Lock: Kensington-style lock slot for securing the unit in shared or public spaces. Common Use Cases 16-camera IP CCTV systems for commercial buildings, retail centres, and warehouses Multi-access-point Wi-Fi deployments in offices, schools, and hospitality venues VoIP phone networks for small to medium businesses Rack-mounted network infrastructure in comms cabinets and server rooms Fibre uplink to a core switch in multi-floor or multi-building installations High-temperature environments where fanless switches are insufficient Technical Specifications Model TL-SG1218MP PoE+ RJ45 Ports 16× 10/100/1000Mbps (Ports 1–16) Non-PoE RJ45 Ports 2× 10/100/1000Mbps (Ports 17–18) Combo SFP Slots 2× Gigabit (shared with Ports 17–18) PoE Standard IEEE 802.3at (PoE+) / 802.3af (PoE) Max PoE Per Port 30W (802.3at) Total PoE Budget 250W Switching Capacity 36 Gbps Packet Forwarding Rate 26.78 Mpps MAC Address Table 8K Packet Buffer Memory 4.1 Mbit Jumbo Frame 10KB QoS 802.1p / DSCP Transmission Method Store-and-Forward Fans 2× (active cooling) Physical Security Lock Yes Chassis Metal Mounting Rack mountable (19″, 1U) Dimensions (W × D × H) 440 × 180 × 44mm Power Supply 100–240V AC, 50/60Hz (internal) Max Power Consumption 21.4W (no PD) / 286.64W (full PoE load) Operating Temperature 0°C to 50°C Standards IEEE 802.3/802.3u/802.3ab/802.3x/802.3af/802.3at/802.1q/802.1p Frequently Asked Questions Is the TL-SG1218MP managed or unmanaged? It is an unmanaged switch. There is no web interface, app, or software required — it operates automatically with no configuration needed. QoS prioritisation (802.1p/DSCP) is applied automatically based on traffic type without any manual setup. How does the TL-SG1218MP compare to the TL-SG1218MPE? Both switches offer 16 PoE+ ports and a 250W budget in a 1U rack chassis. The key difference is management: the TL-SG1218MPE is an Easy Smart switch with a web interface for configuring VLANs, port priority, and IGMP Snooping, while the TL-SG1218MP is fully unmanaged with no configuration interface. Choose the TL-SG1218MPE if you need VLAN or traffic management; choose the TL-SG1218MP for simpler plug-and-play deployments. What is the maximum PoE power per port? Each PoE+ port supports up to 30W (IEEE 802.3at). The total shared PoE budget across all 16 ports is 250W, so plan your device load accordingly. For example, 16 cameras drawing 12W each would use 192W — well within the 250W budget. Can I use the SFP slots with fibre modules? Yes. The two combo SFP slots accept standard Gigabit SFP fibre modules (single-mode or multi-mode, sold separately) for uplink connections to a core switch or to extend your network over long distances. When an SFP module is inserted, the corresponding RJ45 port is disabled. Is it suitable for outdoor or high-temperature environments? The TL-SG1218MP is rated for operating temperatures up to 50°C — higher than most desktop switches — making it suitable for comms cabinets and server rooms without dedicated air conditioning. It is not rated for outdoor use and should be installed in a sheltered, indoor location. How many cameras can I connect? Up to 16 IP cameras can be connected via the PoE+ ports (Ports 1–16). Ports 17–18 are non-PoE uplink ports for connecting to a router or NVR. Ensure the total power draw of all connected cameras does not exceed 250W.

Read more less

TP-Link TL-SL1218P 16-Port PoE+ Rackmount Switch – 150W | 250m Extend Mode | 1U Overview The TP-Link TL-SL1218P is a 1U rackmount PoE+ switch purpose-built for IP camera and surveillance system deployments. With 16 x PoE+ 10/100Mbps ports, a 150W total PoE budget, and a unique 250m Extend Mode for long-distance camera runs, it delivers everything a security installer needs in a single, no-configuration unit. Priority Mode guarantees video quality on Ports 1–8, Isolation Mode separates client traffic with one click, and the combo Gigabit SFP uplink slot provides flexible fibre or copper uplink options. No software, no management interface, no complexity — just plug in and power up. Key Features 16 x PoE+ Ports (Ports 1–16) – IEEE 802.3at/af compliant; up to 30W per port, 150W total PoE budget for powering IP cameras, access points, and other PoE devices. 250m Extend Mode – Extends PoE power and data transmission up to 250 metres over Cat5e/6 cable — purpose-designed for long-distance IP camera runs in large sites, car parks, and perimeter installations. Priority Mode (Ports 1–8) – Guarantees bandwidth and quality of service for video surveillance traffic on the first 8 ports; prevents network congestion from affecting camera streams. Isolation Mode – One-click client traffic separation; prevents connected devices from communicating with each other for improved security and network performance. 2 x Gigabit RJ45 Uplink Ports – High-speed uplinks to your NVR, router, or core switch. 1 x Combo Gigabit SFP Slot – Flexible fibre or copper uplink for long-distance or building-to-building connections. Zero Configuration – Plug-and-play operation; no software, web interface, or management required. 1U Rackmount Form Factor – Standard 19" rack-compatible; 440 × 180 × 44mm. Physical Security Lock – Prevents unauthorised removal from the rack. Use Cases IP camera and NVR installations requiring 16 PoE ports in a single 1U rack unit Long-distance camera runs up to 250m using Extend Mode — car parks, perimeters, warehouses, and large sites Retail, hospitality, and commercial CCTV deployments needing simple plug-and-play PoE switching School, aged care, and healthcare facility surveillance systems Access control and intercom systems requiring multiple PoE-powered endpoints Any installation where a managed switch is unnecessary and simplicity is preferred Technical Specifications Specification Details Model TL-SL1218P PoE Ports 16 × PoE+ 10/100Mbps RJ45 (Ports 1–16) — IEEE 802.3at/af Uplink Ports 2 × 10/100/1000Mbps RJ45 + 1 × Combo Gigabit SFP Total PoE Budget 150W Max PoE Per Port 30W Extend Mode Up to 250m (PoE power & data) Priority Mode Ports 1–8 (Video surveillance priority) Isolation Mode Yes (One-click client separation) Switching Capacity 7.2Gbps Packet Forwarding Rate 5.36Mpps MAC Address Table 8K Jumbo Frame 10KB Transmission Method Store-and-Forward Flow Control IEEE 802.3x Management Unmanaged (No Configuration Required) Physical Security Lock Yes Fans 2 × Internal Fans Power Supply 100–240V AC, 50/60Hz (Internal) Power Consumption (no PoE) 12.71W Power Consumption (max PoE) 172.8W Dimensions (W × D × H) 440 × 180 × 44mm (1U) Weight 2.68kg Network Media 10BASE-T: Cat3/4/5 (max 100m); 100BASE-TX: Cat5/5e (max 100m); 1000BASE-T: Cat5/5e/6+ (max 100m); 1000BASE-X: MMF/SMF Frequently Asked Questions What is Extend Mode and when should I use it? Extend Mode allows the TL-SL1218P to transmit PoE power and data up to 250 metres over Cat5e or Cat6 cable — far beyond the standard 100m Ethernet limit. It is specifically designed for IP camera installations where cameras are located at long distances from the switch, such as car parks, perimeter fences, warehouses, and large commercial sites. Note that in Extend Mode, port speed is reduced to 10Mbps, which is sufficient for standard IP camera streams. What is Priority Mode and which ports does it apply to? Priority Mode applies to Ports 1–8 and guarantees bandwidth priority for devices connected to those ports. This is designed for video surveillance applications where consistent, uninterrupted camera streams are critical. Devices on Ports 1–8 receive priority over traffic on Ports 9–16 when the network is under load. What is Isolation Mode? Isolation Mode prevents connected devices from communicating directly with each other through the switch. All client ports are isolated, meaning cameras and other devices cannot see each other on the network. This improves security by preventing lateral movement between devices and reduces unnecessary broadcast traffic. Is the TL-SL1218P a managed or unmanaged switch? The TL-SL1218P is an unmanaged switch with no web interface, CLI, or SNMP management. It operates via physical DIP switches or buttons for mode selection (Extend, Priority, Isolation). This makes it extremely simple to deploy — ideal for installers who need a reliable PoE switch without the complexity of managed switch configuration. How many IP cameras can the TL-SL1218P power? With 16 PoE+ ports and a 150W total budget, the number of cameras depends on each camera’s power draw. Standard fixed IP cameras typically draw 5–12W, meaning all 16 ports can be used simultaneously within the budget. PTZ cameras or cameras with heaters may draw 15–25W, reducing the number of simultaneously powered ports. Always calculate total PoE load before finalising your design. Can I use the SFP slot for a fibre uplink to an NVR or core switch? Yes. The combo Gigabit SFP slot accepts standard SFP modules (multi-mode or single-mode) for fibre uplink connections. This is useful for building-to-building links or where the NVR or core switch is located more than 100m from the TL-SL1218P. Installer Note: Extend Mode (250m) reduces port speed to 10Mbps — sufficient for most standard IP camera streams but not suitable for high-bitrate 4K cameras or NVR uplinks. Use Extend Mode only on camera ports, not on uplink or NVR ports. Always calculate total PoE load across all 16 ports and ensure it does not exceed the 150W budget, leaving headroom for startup current spikes.

Read more less

24-Port PoE+ Switching Made Simple for SMB and CCTV InstallationsThe TP-Link TL-SG1428PE is a 28-port Gigabit Easy Smart switch that bridges the gap between unmanaged and fully managed switches. With 24 IEEE 802.3at/af PoE+ ports, 4 Gigabit SFP uplink slots, and an intuitive web interface, it gives installers and small business network administrators essential management features — including VLAN segmentation and QoS — without the complexity of a full L2+ managed switch.Key Features 24× Gigabit PoE+ Ports (802.3at/af) — power IP cameras, wireless access points, VoIP phones, and access control devices over a single cable 4× Gigabit SFP Uplink Slots — fibre or copper uplinks for high-speed backbone connectivity 250W Total PoE Budget — up to 30W per port to support demanding PoE+ devices 56 Gbps Switching Capacity — non-blocking performance for high-density deployments 32× VLAN Support — segment network traffic for security, guest access, and IoT isolation QoS (802.1p/DSCP) — prioritise voice and video traffic for consistent performance Easy Smart Web Interface — simplified management without CLI or complex configuration Rack-Mountable, 1U — standard 19-inch rack form factor for network cabinet installation 5-Year Warranty Typical Use Cases PoE switching for IP CCTV systems with up to 24 cameras Small to medium business networks requiring basic VLAN segmentation Wireless access point deployments in offices, schools, and retail environments VoIP phone systems needing QoS prioritisation Network upgrades from unmanaged switches where basic management is needed Technical Specifications Specification Detail Model TL-SG1428PE RJ45 Ports 24× 10/100/1000Mbps PoE+ (802.3at/af) SFP Slots 4× Gigabit SFP Total Ports 28 PoE Standard IEEE 802.3at/af PoE Budget 250W total / 30W per port Switching Capacity 56 Gbps Packet Forwarding Rate 41.7 Mpps MAC Address Table 8K Packet Buffer 4.1 Mbit Jumbo Frame 9KB VLAN 32× 802.1Q VLANs QoS Port-based, 802.1p, DSCP Management Easy Smart Web Interface Form Factor 1U Rack-Mountable Certifications FCC, CE, RoHS Warranty 5 Years Frequently Asked Questions What is the difference between the TL-SG1428PE and the TL-SG3428MP? The TL-SG1428PE is an Easy Smart switch with a simplified web interface, 32 VLANs, and basic QoS — ideal for straightforward CCTV and SMB deployments. The TL-SG3428MP is a full L2+ managed switch with Omada SDN integration, static routing, advanced ACL security, LACP link aggregation, and IGMP snooping, suited to more complex enterprise network environments. How many IP cameras can the TL-SG1428PE power? With a 250W PoE budget and 24 PoE+ ports, it can power up to 24 cameras. Actual capacity depends on each camera’s power draw — cameras drawing 10–15W each will allow the full 24 ports to be used simultaneously. Does the TL-SG1428PE support VLAN isolation for CCTV traffic? Yes. It supports up to 32 802.1Q VLANs, allowing you to isolate CCTV traffic on a dedicated VLAN separate from staff, guest, or IoT networks. Can I use fibre uplinks with this switch? Yes. The 4× Gigabit SFP slots support fibre transceivers for long-distance uplinks to a core switch or NVR, as well as SFP-to-RJ45 copper modules. Does this switch require any special software to manage? No. The TL-SG1428PE is managed entirely through a built-in web interface accessible from any browser on the local network. No additional software, controller, or app is required.

Read more less

8-Port PoE+ Desktop Switch with Extend Mode, Isolation and Priority Control The TP-Link TL-SF1009P is a compact, plug-and-play unmanaged desktop switch with eight 802.3af/at PoE+ ports and a 65W total power budget. Beyond basic PoE switching, it includes Extend Mode for 250m cable runs, Isolation Mode for one-click client traffic separation, and Priority Mode for latency-sensitive devices — making it a feature-rich solution for small CCTV installations, wireless access point deployments, and shared network environments across Australia, all without any configuration required. Key Features 8× PoE+ Ports (802.3af/at): Power IP cameras, access points, VoIP phones, and other PoE/PoE+ devices at up to 30W per port via a single Ethernet cable — no separate power adapters needed. 65W Total PoE Budget: Shared across all eight PoE+ ports, supporting a mix of standard PoE and PoE+ devices simultaneously. Extend Mode (up to 250m): Extends data and PoE power delivery up to 250m at 10Mbps on ports 1–4 or ports 1–8 — ideal for cameras positioned far from the switch in large properties. Priority Mode (Ports 1–2): Prioritises traffic on ports 1 and 2 to guarantee consistent performance for latency-sensitive devices such as IP cameras and NVRs. Isolation Mode (Ports 1–8): One-click client traffic separation prevents devices on different ports from communicating directly with each other — improving security in shared environments such as retail stores, hotels, and apartment buildings. Plug & Play: No configuration, software, or management interface required — modes are toggled via physical buttons on the unit. Fanless & Silent: Completely silent operation — suitable for offices, reception areas, and home installations. Physical Security Lock: Kensington-style lock slot for securing the unit in shared or public spaces. Compact Desktop Form Factor: Small footprint (171 × 98 × 27mm) fits easily on a desk, shelf, or inside a cabinet. Common Use Cases Small CCTV installations with up to 8 IP cameras Long cable run installations using Extend Mode (up to 250m) for perimeter cameras Shared network environments requiring client isolation (e.g. guest Wi-Fi, retail kiosks, hotel rooms) Multi-access-point Wi-Fi deployments in small offices or retail stores VoIP phone deployments in reception areas or small teams Replacing multiple PoE injectors with a single, clean 8-port solution Technical Specifications Model TL-SF1009P Total Ports 9× 10/100Mbps RJ45 PoE+ Ports 8× (Ports 1–8), IEEE 802.3af/at Max PoE Per Port 30W (802.3at) Total PoE Budget 65W Switching Capacity 1.8 Gbps Packet Forwarding Rate 1.3392 Mpps MAC Address Table 2K Jumbo Frame 2KB Transmission Method Store-and-Forward Extend Mode Range Up to 250m at 10Mbps (Ports 1–4 or 1–8) Priority Mode Ports 1–2 (high priority) Isolation Mode Ports 1–8 (one-click client separation) Fan Fanless (silent) Physical Security Lock Yes Power Supply External adapter — 53.5V DC / 1.31A Max Power Consumption 3.6W (no PD) / 77.08W (full PoE load) Dimensions (W × D × H) 171 × 98 × 27mm Operating Temperature 0°C to 40°C Frequently Asked Questions Is the TL-SF1009P managed or unmanaged? It is an unmanaged switch. There is no web interface, app, or software required — it operates automatically with no configuration needed. Extend Mode, Priority Mode, and Isolation Mode are all toggled via physical buttons on the unit. How does Extend Mode work on the TL-SF1009P? Pressing the Extend Mode button reduces port speed to 10Mbps and extends the maximum cable distance from 100m to 250m. On the TL-SF1009P, Extend Mode can be applied to ports 1–4 only, or to all ports 1–8, depending on your deployment needs. This is particularly useful for IP cameras installed at the perimeter of a large property. What is Isolation Mode and when should I use it? Isolation Mode prevents devices connected to ports 1–8 from communicating directly with each other, while still allowing all devices to access the uplink port (port 9). It's ideal for shared environments — such as hotels, retail stores, or apartment buildings — where you want to keep client devices separated for security without needing a managed switch. How does the TL-SF1009P compare to the TL-SG1210MP? The TL-SG1210MP offers Gigabit speeds (vs 100Mbps), a higher 123W PoE budget (vs 65W), PoE Auto Recovery, a combo SFP/RJ45 uplink port, and 10 total ports. The TL-SF1009P is the more compact, lower-cost option for smaller deployments where Gigabit speeds and a higher power budget are not required. Can I power a PTZ camera with this switch? It depends on the PTZ camera's power requirement. The TL-SF1009P supports up to 30W per port (802.3at PoE+), which covers most compact PTZ cameras. High-power PTZ cameras requiring more than 30W will need a dedicated power supply or a higher-wattage PoE injector. What is the total PoE budget and how should I plan my deployment? The total shared PoE budget is 65W across all eight PoE+ ports. For example, 8 cameras drawing 8W each would use 64W — just within budget. If you have higher-power devices, calculate your total load carefully. For deployments requiring more headroom, consider the TL-SG1210MP (123W) or TL-SG1218MP (250W).

Read more less

TP-Link TL-SG1005LP – 5-Port Gigabit Desktop Switch with 4-Port PoE+ The TP-Link TL-SG1005LP is a compact, fanless 5-port Gigabit switch with PoE+ on four of its five ports — making it an ideal solution for small IP camera installations, wireless access point deployments, and VoIP phone setups where a full-sized switch is unnecessary. With a 40W total PoE budget, IEEE 802.3af/at compliance, and plug-and-play operation, it delivers data and power over a single cable to up to four devices without any configuration required. Key Features 4 × PoE+ Ports (Ports 1–4): IEEE 802.3af/at compliant, delivering up to 30W per port for IP cameras, wireless APs, VoIP phones, and access control devices. 40W Total PoE Budget: Shared across all four PoE ports for powering multiple devices simultaneously from a single switch. 5 × Gigabit Ports: All five ports support 10/100/1000Mbps with Auto-Negotiation and Auto MDI/MDIX — no crossover cables required. Fanless Silent Operation: No moving parts — completely silent, suitable for offices, reception areas, and noise-sensitive environments. Plug and Play: No configuration, software, or web interface required — connect and power on. 802.1p/DSCP QoS: Prioritises latency-sensitive traffic such as VoIP and video streams for consistent performance. IGMP Snooping: Optimises multicast traffic delivery, reducing unnecessary bandwidth usage from IP camera streams. Compact Desktop Form Factor: 99.8 × 98 × 25mm — fits neatly on a desk, shelf, or inside a small cabinet. Store-and-Forward Switching: Error-free packet forwarding for reliable data transmission. Ideal Use Cases Powering and connecting 1–4 IP cameras in a small CCTV installation without separate PoE injectors. Deploying a wireless access point and a VoIP phone from a single compact switch in a small office or retail space. Adding PoE capability to a location where only a non-PoE switch or router port is available, using the uplink port (Port 5) to connect upstream. Home office setups requiring a small Gigabit switch with PoE for a camera doorbell, AP, or IP phone. Temporary or permanent installations in cabinets, server rooms, or comms cupboards where space is limited. Technical Specifications Specification Detail Model TL-SG1005LP Total Ports 5 × 10/100/1000Mbps RJ45 (Auto MDI/MDIX) PoE Ports 4 (Ports 1–4) PoE Standard IEEE 802.3af / IEEE 802.3at (PoE+) PoE Power per Port Up to 30W Total PoE Budget 40W Switching Capacity 10Gbps Packet Forwarding Rate 7.44Mpps MAC Address Table 2K Jumbo Frame 16KB QoS 802.1p / DSCP IGMP Snooping Yes Transfer Method Store-and-Forward Fan Fanless (silent) Power Supply External adapter (53.5VDC / 0.81A) Power Consumption (no PD) 4.12W @ 220V/50Hz Power Consumption (max PoE) 47.5W @ 220V/50Hz Operating Temperature 0°C – 40°C Dimensions 99.8 × 98 × 25 mm Certifications FCC, CE, RoHS SKU TL-SG1005LP Barcode (EAN) 6935364052720 What’s in the Box 1 × TL-SG1005LP 5-Port Gigabit PoE+ Switch 1 × Power Adapter Installation Guide Frequently Asked Questions Which ports support PoE on the TL-SG1005LP? Ports 1 through 4 are PoE+ capable. Port 5 is a standard Gigabit uplink port without PoE, used to connect the switch to your router or upstream network. What is the total PoE power budget? The TL-SG1005LP has a total PoE budget of 40W shared across all four PoE ports. Each port can deliver up to 30W individually, but the combined draw across all four ports cannot exceed 40W. How many IP cameras can I power with this switch? Up to four cameras simultaneously. The number depends on each camera’s PoE power draw. For example, four cameras drawing 8W each would total 32W — within the 40W budget. Higher-wattage cameras (e.g. PTZ cameras at 25–30W) will reduce the number that can be powered concurrently. Does it require any configuration? No. The TL-SG1005LP is fully plug and play. Connect your devices and power on — no web interface, software, or CLI configuration is required. Can I use it with non-PoE devices? Yes. The switch automatically detects whether a connected device requires PoE. Non-PoE devices (such as computers or NVRs) connect normally via Ethernet without any risk of damage from the PoE circuitry. Is it suitable for use in a small office or home environment? Yes. The fanless design means it operates in complete silence, making it suitable for desks, reception areas, and home offices. Its compact footprint (approximately 10 × 10cm) means it fits almost anywhere. What is the difference between the TL-SG1005LP and the TL-SG116P? The TL-SG1005LP has 5 ports (4 PoE+) with a 40W budget — ideal for small installations with 1–4 PoE devices. The TL-SG116P has 16 ports (all PoE+) with a 120W budget, suited to larger camera or AP deployments. Choose the TL-SG1005LP for compact, cost-effective setups and the TL-SG116P when you need to power more devices.

Read more less

TP-Link TL-SG105PE 5-Port Gigabit PoE+ Easy Smart Switch Reliable PoE+ Switching for IP Cameras, VoIP & Smart Devices The TP-Link TL-SG105PE is a compact, fanless 5-port Gigabit smart switch with 4 PoE+ ports and a 65 W total power budget. It delivers both data and power over a single Ethernet cable — making it an ideal choice for IP security cameras, wireless access points, and VoIP phones in homes, small offices, and commercial installations across Australia. Extend Mode pushes PoE reach up to 250 m for remote camera positions, and PoE Auto Recovery automatically restarts unresponsive powered devices without manual intervention. Key Features 4 × 802.3af/at PoE+ ports — up to 30 W per port, 65 W total PoE budget 5 × 10/100/1000 Mbps Gigabit RJ45 ports with Auto-Negotiation and Auto MDI/MDIX Fanless, silent operation — suitable for noise-sensitive environments PoE Auto Recovery — automatically restarts unresponsive PoE devices Extend Mode — supports PoE transmission up to 250 m at 10 Mbps VLAN support — up to 32 active VLANs (MTU, Port, and Tag-based) QoS with Port-Based, 802.1p, and DSCP priority — 4 priority queues IGMP Snooping V1/V2/V3, Port Mirroring, Loop Prevention, Cable Diagnostics Web-based GUI and Easy Smart Configuration Utility for simple setup 10 Gbps switching capacity, 7.44 Mpps forwarding rate Use Cases IP CCTV Systems: Power and connect up to 4 PoE IP cameras without separate power supplies — ideal for small surveillance installations. Wireless Access Points: Deploy PoE-powered APs throughout a small office or retail space without additional power cabling. VoIP Phones: Prioritise voice traffic with QoS to ensure call quality on small business phone systems. Long-Run Installations: Use Extend Mode to push PoE up to 250 m for remote camera positions where cable runs are long. Small Office Networks: Segment traffic with VLANs and monitor network health with port mirroring and cable diagnostics. Specifications Specification Detail Model TL-SG105PE Total Ports 5 × 10/100/1000 Mbps RJ45 PoE Ports Ports 1–4 (802.3af/at PoE+) PoE Power Per Port Up to 30 W Total PoE Budget 65 W Switching Capacity 10 Gbps Forwarding Rate 7.44 Mpps MAC Address Table 2K Packet Buffer 1.5 Mb Jumbo Frame 16 KB VLAN Up to 32 active VLANs (4K VLAN IDs) QoS Port-Based / 802.1p / DSCP, 4 queues Extend Mode Up to 250 m at 10 Mbps Power Supply External adapter — 53.5 V DC / 1.31 A Max Power Consumption 4.52 W (no PD) / 75.16 W (full PoE load) Cooling Fanless Standards IEEE 802.3i/u/ab/af/at/x, 802.1q, 802.1p Weight 0.76 kg Frequently Asked Questions How many PoE cameras can I connect to the TL-SG105PE? You can connect up to 4 PoE-powered devices (ports 1–4). The total PoE budget is 65 W — if each camera draws 15 W, all 4 ports can run simultaneously at full load. Higher-draw devices (e.g., PTZ cameras at 25–30 W) will reduce the number of simultaneous powered ports. Does this switch require any configuration out of the box? No. It works plug-and-play for basic switching and PoE. The web GUI and Easy Smart Configuration Utility are available for advanced features like VLANs, QoS, and port mirroring when needed. Is the TL-SG105PE compatible with non-TP-Link PoE cameras? Yes. It complies with the IEEE 802.3af/at standard, so it is compatible with any standards-compliant PoE or PoE+ device regardless of brand. What is Extend Mode and when should I use it? Extend Mode reduces port speed to 10 Mbps to extend PoE transmission range up to 250 m. It is useful for remote camera positions where the cable run exceeds the standard 100 m Ethernet limit. What is PoE Auto Recovery? PoE Auto Recovery periodically checks the status of connected PoE devices. If a device becomes unresponsive (e.g., a frozen IP camera), the switch automatically power-cycles that port to restart the device — without any manual intervention. Does the switch have a fan? No. The TL-SG105PE is completely fanless, making it silent and suitable for offices, reception areas, server cabinets, or any noise-sensitive environment.

Read more less

Simple, Reliable PoE Power for Cameras and Access Points The TP-Link TL-SF1005LP is a compact, plug-and-play desktop switch that delivers both data and power over a single Ethernet cable to up to four PoE devices. With a 41W total PoE budget, Extend Mode for long cable runs up to 250m, and fanless silent operation, it's an ideal solution for small CCTV installations, IP phone deployments, and wireless access point setups in homes, small offices, and retail environments across Australia. Key Features 4× PoE Ports (802.3af): Power IP cameras, access points, VoIP phones, and other 802.3af-compliant devices without separate power adapters. 41W Total PoE Budget: Shared across all four PoE ports — sufficient for most small-scale deployments with standard PoE devices. Extend Mode (up to 250m): Push data and power up to 250 metres at 10Mbps on a single cable run — ideal for cameras positioned far from the switch. Priority Mode (Ports 1–2): Prioritises traffic on ports 1 and 2 to ensure consistent performance for latency-sensitive devices such as IP cameras or VoIP phones. Plug & Play: No configuration, software, or management interface required — simply connect and go. Fanless & Silent: Completely silent operation makes it suitable for office desks, reception areas, and home installations. Compact Desktop Form Factor: Small footprint (100 × 98 × 25mm) fits easily on a desk, shelf, or inside a cabinet. Physical Security Lock: Kensington-style lock slot for securing the unit in shared or public spaces. Common Use Cases Powering 1–4 IP security cameras in small CCTV systems Connecting and powering wireless access points in small offices or retail stores VoIP phone deployments in reception areas or small teams Extending camera cable runs beyond the standard 100m Ethernet limit Home network expansion with PoE device support Technical Specifications Model TL-SF1005LP Total Ports 5× 10/100Mbps RJ45 PoE Ports 4× (Ports 1–4), IEEE 802.3af Total PoE Budget 41W Switching Capacity 1 Gbps Packet Forwarding Rate 0.744 Mpps MAC Address Table 2K Extend Mode Range Up to 250m at 10Mbps (Ports 1–4) Priority Mode Ports 1–2 (high priority) Transmission Method Store-and-Forward Power Supply External adapter — 53.5V DC / 0.81A Max Power Consumption 1.9W (no PD) / 47W (full PoE load) Fan Fanless (silent) Physical Security Lock Yes Dimensions (W × D × H) 100 × 98 × 25mm Operating Temperature 0°C to 40°C Operating Humidity 10–90% RH (non-condensing) Certifications FCC, CE, RoHS In the Box TL-SF1005LP, Power Adapter, Installation Guide Frequently Asked Questions Is the TL-SF1005LP managed or unmanaged? It is an unmanaged switch. There is no web interface, app, or software required — it operates automatically with no configuration needed. Mode switching (Extend/Priority) is done via physical buttons on the unit. What is the maximum PoE power per port? Each PoE port supports up to 15.4W (IEEE 802.3af standard). The total shared PoE budget across all four ports is 41W, so plan your device load accordingly. Can I use it with 802.3at (PoE+) devices? The TL-SF1005LP supports 802.3af only (up to 15.4W per port). It is not compatible with 802.3at PoE+ devices that require more than 15.4W. For PoE+ devices, consider a PoE+ switch from the TP-Link range. How does Extend Mode work? Pressing the Extend Mode button reduces port speed to 10Mbps and extends the maximum cable distance from 100m to 250m on ports 1–4. This is particularly useful for IP cameras installed at the perimeter of a property. Can I power a PTZ camera with this switch? It depends on the PTZ camera's power requirement. Most compact PTZ cameras draw under 15.4W and are 802.3af compatible — check your camera's spec sheet. High-power PTZ cameras typically require 802.3at PoE+ or a dedicated power supply. Does it support VLAN or QoS? No. As an unmanaged switch, it does not support VLAN, QoS, or any advanced traffic management features. The Priority Mode button provides basic port prioritisation for ports 1–2 only.

Read more less

Power and Connect Your Devices with the TP-Link TL-SF1006PThe TP-Link TL-SF1006P is a compact 6-port Fast Ethernet desktop switch designed for small offices, home networks, and security installations. With four built-in PoE+ ports, it delivers both data and power over a single cable — eliminating the need for separate power adapters for IP cameras, VoIP phones, and wireless access points.Key Features 6× 10/100 Mbps RJ45 Ports — reliable Fast Ethernet connectivity for everyday networking 4× PoE+ Ports (802.3af/at) — power IP cameras, access points, and VoIP phones without extra cabling 67W Total PoE Budget — up to 30W per port to support demanding PoE+ devices Extend Mode — transmit data and power up to 250m on ports 1–4 for long-distance runs Priority Mode — ports 1–2 get traffic priority for latency-sensitive applications like VoIP and IP cameras Fanless Design — silent operation, ideal for office and home environments Plug and Play — no configuration required; simply connect and go Physical Security Lock — prevents accidental disconnection Typical Use Cases Powering IP security cameras in small CCTV installations Connecting VoIP phones in small offices without separate power supplies Extending network reach to wireless access points in hard-to-wire locations Home office networking with mixed PoE and non-PoE devices Technical Specifications Specification Detail Ports 6× 10/100 Mbps RJ45 (Ports 1–4 PoE+) PoE Standard IEEE 802.3af/at PoE Budget 67W total / 30W per port Switching Capacity 1.2 Gbps Packet Forwarding Rate 0.8928 Mpps MAC Address Table 2K Transmission Method Store-and-Forward Extend Mode Range Up to 250m (Ports 1–4) Fan Fanless Power Supply External adapter (53.5V DC / 1.31A) Max Power Consumption 1.9W (no PD) / 74W (full PoE load) Dimensions (W×D×H) 158 × 101 × 25 mm Operating Temperature 0–40°C Certifications FCC, CE, RoHS Warranty 5 Years What's in the Box TL-SF1006P Switch External Power Adapter Installation Guide Frequently Asked Questions Can I use non-PoE devices on this switch? Yes. All 6 ports support standard Ethernet. Ports 5–6 are non-PoE data-only ports. Non-PoE devices connected to ports 1–4 will receive data but no power. What is Extend Mode and when should I use it? Extend Mode allows data and power transmission up to 250m on ports 1–4 by reducing the link speed to 10 Mbps. It's ideal for IP cameras located far from the switch, such as in car parks or large properties. What is Priority Mode? Priority Mode gives ports 1–2 higher traffic priority, ensuring consistent performance for latency-sensitive devices like IP cameras or VoIP phones even when the network is busy. Does this switch require any software or configuration? No. The TL-SF1006P is fully plug-and-play with no software, login, or configuration required. Is this switch rack-mountable? No. The TL-SF1006P is a desktop form factor switch and is not designed for rack mounting.

Read more less

8-Port Desktop Switch with 4 PoE Ports, Extend Mode and Priority Control The TP-Link TL-SF1008LP is a compact, plug-and-play unmanaged desktop switch with four 802.3af PoE ports, a 41W total power budget, and Extend Mode for cable runs up to 250m. With Priority Mode for latency-sensitive devices and a completely fanless design, it's a practical, low-cost solution for small CCTV installations, IP phone deployments, and wireless access point setups in homes, small offices, and retail environments across Australia. Key Features 4× PoE Ports (802.3af, Ports 1–4): Power IP cameras, access points, VoIP phones, and other 802.3af-compliant devices without separate power adapters — data and power over a single Ethernet cable. 41W Total PoE Budget: Shared across all four PoE ports — sufficient for most small deployments with standard 802.3af devices. 8× 10/100Mbps RJ45 Ports: Four PoE-enabled ports (1–4) plus four standard ports (5–8) for connecting non-PoE devices such as PCs, NVRs, and routers. Extend Mode (up to 250m): Pressing the Extend Mode button reduces port speed to 10Mbps and extends the maximum cable distance from 100m to 250m on ports 1–4 — ideal for cameras positioned far from the switch. Priority Mode (Ports 1–2): Prioritises traffic on ports 1 and 2 to guarantee consistent performance for latency-sensitive devices such as IP cameras and VoIP phones. Plug & Play: No configuration, software, or management interface required — Extend Mode and Priority Mode are toggled via physical buttons on the unit. Fanless & Silent: Completely silent operation — suitable for offices, reception areas, and home installations. Physical Security Lock: Kensington-style lock slot for securing the unit in shared or public spaces. Compact Form Factor: Small desktop footprint (171 × 98 × 27mm) fits easily on a desk, shelf, or inside a cabinet. Common Use Cases Powering 1–4 IP security cameras in small CCTV systems Connecting and powering wireless access points in small offices or retail stores VoIP phone deployments in reception areas or small teams Extending camera cable runs beyond the standard 100m Ethernet limit using Extend Mode Home network expansion with PoE device support Replacing multiple PoE injectors with a single, clean 4-port solution Technical Specifications Model TL-SF1008LP Total Ports 8× 10/100Mbps RJ45 PoE Ports 4× (Ports 1–4), IEEE 802.3af Total PoE Budget 41W Switching Capacity 1.6 Gbps MAC Address Table 2K Transmission Method Store-and-Forward Extend Mode Range Up to 250m at 10Mbps (Ports 1–4) Priority Mode Ports 1–2 (high priority) Fan Fanless (silent) Physical Security Lock Yes Power Supply External adapter — 53.5V DC / 0.81A Max Power Consumption 2.2W (no PD) / 47.1W (full PoE load) Dimensions (W × D × H) 171 × 98 × 27mm Operating Temperature 0°C to 40°C Operating Humidity 10–90% RH (non-condensing) Certifications FCC, CE, RoHS In the Box TL-SF1008LP, Power Adapter, Installation Guide Frequently Asked Questions What is the difference between the TL-SF1008LP and the TL-SF1005LP? The TL-SF1008LP has 8 total ports (4 PoE + 4 standard) compared to the TL-SF1005LP's 5 total ports (4 PoE + 1 standard). Both share the same 41W PoE budget, Extend Mode, and Priority Mode features. Choose the TL-SF1008LP if you need more non-PoE ports for connecting additional devices such as a PC, NVR, or router alongside your PoE cameras. Is the TL-SF1008LP managed or unmanaged? It is an unmanaged switch. There is no web interface, app, or software required — it operates automatically with no configuration needed. Extend Mode and Priority Mode are toggled via physical buttons on the unit. What is the maximum PoE power per port? Each PoE port supports up to 15.4W (IEEE 802.3af standard). The total shared PoE budget across all four ports is 41W, so plan your device load accordingly. For example, four cameras drawing 10W each would use 40W — just within the 41W budget. Can I use it with 802.3at (PoE+) devices? The TL-SF1008LP supports 802.3af only (up to 15.4W per port). It is not compatible with 802.3at PoE+ devices that require more than 15.4W. For PoE+ devices, consider the TL-SF1009P (65W, 8 PoE+ ports) or TL-SG1210MP (123W, 8 PoE+ Gigabit ports). How does Extend Mode work? Pressing the Extend Mode button reduces port speed to 10Mbps on ports 1–4 and extends the maximum cable distance from 100m to 250m. This is particularly useful for IP cameras installed at the perimeter of a large property where running a new cable closer to the switch is impractical. What is the difference between the TL-SF1008LP and the TL-SF1009P? The TL-SF1009P has 9 ports with 8 PoE+ ports (802.3at, up to 30W per port) and a 65W total budget, plus Isolation Mode for client traffic separation. The TL-SF1008LP has 8 ports with 4 PoE ports (802.3af, up to 15.4W per port) and a 41W budget. Choose the TL-SF1009P if you need more PoE ports, higher per-port power, or client isolation; choose the TL-SF1008LP for a simpler, lower-cost 4-port PoE solution.

Read more less

Mercusys MS108G 8-Port Gigabit Desktop Switch Instant Gigabit Network Expansion — Plug In and Go The Mercusys MS108G is a compact, plug-and-play 8-port Gigabit desktop switch that instantly expands your wired network with no configuration required. With eight 10/100/1000 Mbps auto-negotiation ports, Green Ethernet power-saving technology, and a smartphone-sized form factor, it’s the straightforward choice for adding wired Gigabit connectivity to homes, small offices, and study spaces across Australia. Key Features 8 × 10/100/1000 Mbps Gigabit RJ45 ports with Auto-Negotiation and Auto MDI/MDIX Plug-and-play — no configuration, no software, no setup required Green Ethernet technology — automatically adjusts power consumption based on link status and cable length, saving up to 82% energy Compact desktop form factor — approximately smartphone-sized at 127 × 60.3 × 22 mm Store-and-forward switching for reliable, error-free data transmission 9 KB Jumbo Frame support for large data transfers Compatible with 4K TVs, computers, printers, IP cameras, gaming consoles, and more Use Cases Home Networks: Add 8 wired Gigabit ports to your router or modem to connect smart TVs, gaming consoles, desktop PCs, and NAS devices simultaneously. Small Offices: Quickly expand a wired network at a desk or workstation cluster without any IT configuration. IP Camera Installations: Provide wired Gigabit connections for IP cameras or NVRs in small surveillance setups where PoE is not required. Student Accommodation: Compact size and plug-and-play operation make it ideal for dorm rooms or shared living spaces. Home Entertainment: Connect multiple media devices in a lounge or entertainment room to a single wired Gigabit network. Specifications Specification Detail Model MS108G Ports 8 × 10/100/1000 Mbps RJ45 (Auto-Negotiation, Auto MDI/MDIX) Data Rates 10/100/1000 Mbps half-duplex; 20/200/2000 Mbps full-duplex Transfer Method Store and Forward Buffer Capacity 64 KB Jumbo Frame 9 KB Standards IEEE 802.3, IEEE 802.3u, IEEE 802.3x, CSMA/CD Power Supply External adapter — 9 V / 0.6 A Green Ethernet Yes — up to 82% power saving Dimensions (W × D × H) 127 × 60.3 × 22 mm Weight 0.24 kg Configuration Plug-and-play — none required Frequently Asked Questions Does the MS108G require any setup or software? No. Simply connect the switch to your router or modem via an Ethernet cable, plug in the power adapter, and connect your devices. No software, login, or configuration is required. Can I use the MS108G to connect IP cameras? Yes, for cameras that use their own power supply (non-PoE). The MS108G does not supply Power over Ethernet — if you need to power cameras via the network cable, consider a PoE switch such as the TP-Link TL-SG105PE or TL-SG2210MP. Is the MS108G compatible with my existing router? Yes. The MS108G is a standard unmanaged Gigabit switch compatible with any router, modem, or network device with an Ethernet port, regardless of brand or ISP. What does Green Ethernet do? Green Ethernet automatically detects the cable length and link status of each port and reduces power output accordingly. Ports with shorter cables or no active connection use significantly less power — saving up to 82% compared to standard switches. Can I stack or daisy-chain multiple MS108G switches? Yes. You can connect multiple unmanaged switches together to expand your network further. Connect one port on the second switch to a port on the first switch via Ethernet. Note that each additional switch hop adds a small amount of latency.

Read more less

Power and Connect Up to 24 IP Cameras or PoE Devices — No Configuration Required The TP-Link TL-SL1226P is a rack-mountable 24-port PoE+ unmanaged switch built for security installers and network professionals who need reliable, high-power PoE delivery without the complexity of managed switching. With a 250W PoE budget, 250m Extend Mode, and plug-and-play operation, it's one of the most practical switches for IP camera deployments across Australian commercial and residential installations. Key Features 24× PoE+ Ports (802.3at/af) — Power and connect IP cameras, VoIP phones, and wireless access points over a single Cat5e/6 cable, up to 30W per port. 250W Total PoE Budget — Sufficient headroom to simultaneously power a full deployment of standard IP cameras or mixed PoE devices. Extend Mode (up to 250m) — Transmit data and power up to 250 metres at 10 Mbps — ideal for large sites where cameras are positioned far from the switch. Priority Mode — Ports 1–8 are automatically assigned high priority, ensuring video streams from critical cameras are never starved of bandwidth. Isolation Mode — One-click client traffic separation improves network security and performance in multi-tenant or shared environments. 2× Gigabit RJ45 Uplinks + 2× Combo SFP Slots — Flexible uplink options for connecting to your core network switch or fibre backbone. Plug and Play — No software, no login, no configuration. Unbox, rack, and connect. Physical Security Lock — Prevents accidental disconnection of the power cable in rack environments. Use Cases IP CCTV Installations — Power and connect up to 24 IP cameras from a single switch in commercial or multi-site surveillance deployments. VoIP Phone Systems — Deliver power and data to desk phones across an office floor without separate power adaptors. Wireless Access Point Deployments — Power ceiling-mounted APs throughout a building from a central comms room. Large-Site Surveillance (Extend Mode) — Reach cameras in car parks, warehouses, or perimeter locations up to 250m away without a media converter. Education & Hospitality — Isolation Mode makes it suitable for guest networks or student lab environments requiring traffic separation. Technical Specifications Specification Detail Model TL-SL1226P PoE Ports 24× 10/100 Mbps RJ45 (PoE+, 802.3at/af) Uplink Ports 2× Gigabit RJ45 + 2× Combo Gigabit SFP PoE Power Budget 250W total / up to 30W per port Switching Capacity 8.8 Gbps MAC Address Table 8K Extend Mode Range Up to 250m at 10 Mbps Dimensions (W×D×H) 440 × 180 × 44 mm (1U Rack) Power Supply 100–240V AC, 50/60 Hz Max Power Consumption 18.32W (no PD) / 294W (250W PD load) Cooling 2× Internal Fans Physical Security Lock Yes Network Media Cat3/4/5 (10BASE-T), Cat5/5e (100BASE-TX), Cat5e/6+ (1000BASE-T), MMF/SMF (1000BASE-X) Certifications FCC, CE, RoHS Frequently Asked Questions How many IP cameras can this switch power simultaneously? With a 250W PoE budget and up to 30W per port, the TL-SL1226P can power up to 24 cameras. In practice, the number depends on each camera's power draw. Most standard IP cameras consume 5–15W, so you can typically run a full 24-camera deployment comfortably within the budget. What is Extend Mode and when should I use it? Extend Mode reduces the port speed to 10 Mbps and extends the PoE transmission range from the standard 100m up to 250m. Use it when cameras are located far from the switch — such as in car parks, warehouses, or along building perimeters — to avoid running additional cable or installing a media converter. Does this switch require any software or configuration? No. The TL-SL1226P is fully unmanaged and plug-and-play. Simply connect your devices and it operates automatically. Extend Mode, Priority Mode, and Isolation Mode are toggled via physical DIP switches on the unit — no login or software required. Can I connect this to a fibre uplink? Yes. The two combo Gigabit SFP slots accept standard SFP modules (sold separately), allowing you to connect to a fibre backbone or a core managed switch in your comms room. Is this switch rack-mountable? Yes. The TL-SL1226P is a 1U rack-mount unit (440mm wide) and includes rack-mount hardware in the box, making it suitable for standard 19-inch equipment racks. What's the difference between Priority Mode and Isolation Mode? Priority Mode assigns higher bandwidth priority to ports 1–8, ensuring video streams from critical cameras are not disrupted by other traffic. Isolation Mode prevents connected devices from communicating directly with each other through the switch, improving security and reducing broadcast traffic — useful in multi-tenant or guest network scenarios.

Read more less

TP-Link TL-SG1210P – 10-Port Gigabit Desktop Switch with 8-Port PoE+ and SFP Slot The TP-Link TL-SG1210P is a fanless 10-port Gigabit switch with PoE+ on eight ports, a dedicated Gigabit SFP fibre slot, and a 63W total PoE budget — all in a compact desktop form factor. Designed for small to medium IP camera installations, wireless AP deployments, and mixed wired/wireless office networks, it delivers data and power over a single cable to up to eight devices with no configuration required. The SFP slot adds flexibility for fibre uplinks to a core switch or NVR over longer distances. Key Features 8 × PoE+ Ports (Ports 1–8): IEEE 802.3af/at compliant, delivering up to 30W per port for IP cameras, wireless APs, VoIP phones, and access control devices. 63W Total PoE Budget: Sufficient to simultaneously power multiple cameras and APs from a single switch. 1 × Gigabit SFP Slot: Supports single-mode and multi-mode fibre transceivers for long-distance uplinks to a core switch, NVR, or fibre backbone — without running copper cable. 9 × Gigabit RJ45 Ports + 1 SFP: 10 total ports with full 10/100/1000Mbps Auto-Negotiation and Auto MDI/MDIX on all copper ports. Fanless Silent Operation: No moving parts — completely silent, suitable for offices, reception areas, and noise-sensitive environments. Plug and Play: No configuration, software, or web interface required — connect and power on. 802.1p/DSCP QoS: Prioritises latency-sensitive traffic such as VoIP and IP camera streams for consistent performance. IGMP Snooping: Optimises multicast traffic from IP cameras, reducing unnecessary bandwidth consumption across the network. Physical Security Lock: Kensington-style lock slot for securing the switch in accessible locations. 20Gbps Switching Capacity: Non-blocking architecture ensures full-speed performance across all ports simultaneously. Ideal Use Cases Powering and connecting up to 8 IP cameras in a CCTV installation without separate PoE injectors or power supplies. Deploying multiple wireless access points across an office, retail space, or warehouse from a single switch. Mixed installations combining IP cameras, APs, VoIP phones, and wired computers on a single compact switch. Using the SFP slot for a fibre uplink to a core switch or NVR located beyond the 100-metre copper cable limit. Small business networks requiring a silent, desktop-sized PoE switch with fibre uplink capability. Replacing multiple PoE injectors with a single managed-free switch for cleaner, more cost-effective installations. Technical Specifications Specification Detail Model TL-SG1210P RJ45 Ports 9 × 10/100/1000Mbps (8 PoE+, 1 standard) SFP Slot 1 × Gigabit SFP (MMF & SMF) PoE Ports Ports 1–8 (IEEE 802.3af/at) PoE Power per Port Up to 30W Total PoE Budget 63W Switching Capacity 20Gbps MAC Address Table 4K QoS 802.1p / DSCP IGMP Snooping Yes Transfer Method Store-and-Forward Fan Fanless (silent) Physical Security Security lock slot Power Supply External adapter (53.5VDC / 1.31A) Power Consumption (no PD) 7.11W @ 220V/50Hz Power Consumption (max PoE) 78.13W @ 220V/50Hz Operating Temperature 0°C – 40°C Dimensions 209 × 126 × 26 mm Weight 1.26kg Certifications CE, FCC, RoHS SKU TL-SG1210P Barcode (EAN) 1210002617062 What’s in the Box 1 × TL-SG1210P 10-Port Gigabit PoE+ Switch 1 × Power Adapter Installation Guide Frequently Asked Questions Which ports support PoE on the TL-SG1210P? Ports 1 through 8 are PoE+ capable (IEEE 802.3af/at). Port 9 is a standard Gigabit RJ45 uplink port, and Port 10 is the Gigabit SFP slot — neither supports PoE. What is the total PoE power budget? The TL-SG1210P has a 63W total PoE budget shared across all eight PoE ports. Each port can deliver up to 30W individually, but the combined draw across all eight ports cannot exceed 63W. How many IP cameras can I power simultaneously? Up to eight cameras. The actual number depends on each camera’s PoE power draw. For example, eight cameras drawing 7W each totals 56W — within the 63W budget. Higher-wattage cameras (e.g. PTZ cameras at 25–30W) will reduce the number that can be powered concurrently. What SFP transceivers are compatible with the SFP slot? The SFP slot supports standard Gigabit SFP transceivers for both multi-mode fibre (MMF, e.g. 1000BASE-SX) and single-mode fibre (SMF, e.g. 1000BASE-LX). TP-Link-branded SFP modules are recommended for guaranteed compatibility. SFP transceivers are sold separately. Does it require any configuration? No. The TL-SG1210P is fully plug and play. Connect your devices and power on — no web interface, software, or CLI configuration is required. What is the difference between the TL-SG1210P and the TL-SG1005LP? The TL-SG1210P has 10 ports (8 PoE+) with a 63W budget and a Gigabit SFP slot for fibre uplinks. The TL-SG1005LP has 5 ports (4 PoE+) with a 40W budget and no SFP slot. Choose the TL-SG1210P for larger installations requiring more PoE ports, higher budget, or fibre connectivity. What is the difference between the TL-SG1210P and the TL-SG116P? The TL-SG116P has 16 PoE+ ports with a 120W budget and is designed for larger deployments. The TL-SG1210P has 8 PoE+ ports with a 63W budget plus a Gigabit SFP slot, making it better suited for medium-sized installations that also need a fibre uplink option.

Read more less

16-Port Gigabit PoE+ Switch Built for CCTV and SMB Networks The TP-Link TL-SG1218MPE is a JetStream Easy Smart switch that combines 16 Gigabit PoE+ ports, a 192W power budget, and intelligent traffic management in a rack-mountable 1U chassis. Designed for small to medium business surveillance systems, wireless deployments, and IP phone networks, it delivers the performance and control of a managed switch with the simplicity of easy smart configuration — no advanced networking expertise required. Key Features 16× Gigabit PoE+ Ports (802.3at/af): Power and connect IP cameras, wireless access points, VoIP phones, and other PoE/PoE+ devices across all 16 ports simultaneously. 192W Total PoE Budget: One of the highest PoE budgets in its class — supports a full deployment of 16 standard PoE cameras or a mixed load of PoE+ devices. 2× SFP Fibre Uplink Ports: Connect to fibre backbone switches or extend your network over long distances using single-mode or multi-mode fibre. QoS (Quality of Service): Prioritises video and voice traffic to ensure smooth, uninterrupted camera feeds and VoIP calls even under heavy network load. IGMP Snooping: Optimises multicast traffic for IPTV and IP camera streams, reducing unnecessary bandwidth consumption across the network. Port Priority: Assign priority to specific ports to guarantee performance for latency-sensitive devices such as IP cameras and NVRs. Intelligent PoE Power Management: Automatically monitors and manages PoE power distribution to protect against overload. 802.1Q VLAN Support: Segment your network for improved security and traffic isolation between cameras, staff devices, and guest networks. Rack Mountable (1U): Standard 19-inch rack form factor (440 × 180 × 44mm) for clean, professional installations in comms cabinets and server rooms. 36 Gbps Switching Capacity: Non-blocking switching fabric handles high-bandwidth video streams from multiple cameras without bottlenecks. Common Use Cases 16-camera IP CCTV systems for retail, warehouses, and commercial buildings Multi-access-point Wi-Fi deployments in offices, schools, and hospitality venues VoIP phone networks for small to medium businesses Mixed PoE/PoE+ deployments requiring high total power budgets Network segmentation with VLAN for security-conscious installations Fibre uplink to a core switch in multi-floor or multi-building networks Technical Specifications Model TL-SG1218MPE RJ45 Ports 16× 10/100/1000Mbps (all PoE+) SFP Ports 2× Gigabit SFP (fibre uplink) PoE Standard IEEE 802.3at (PoE+) / 802.3af (PoE) Total PoE Budget 192W Switching Capacity 36 Gbps Packet Forwarding Rate 23.8 Mpps MAC Address Table 8K Packet Buffer Memory 4.1 Mbit Jumbo Frame 9KB VLAN 802.1Q VLAN QoS Yes (802.1p) IGMP Snooping Yes Fans 2× (active cooling) Physical Security Lock Yes Mounting Rack mountable (19″, 1U) Dimensions (W × D × H) 440 × 180 × 44mm Power Supply 100–240V AC, 50/60Hz (internal) Max Power Consumption 18.73W (no PD) / 217.22W (full PoE load) Standards IEEE 802.3/802.3u/802.3ab/802.3x/802.3af/802.3at/802.1q/802.1p Management Easy Smart (web UI) Frequently Asked Questions What is an “Easy Smart” switch? Easy Smart is TP-Link's simplified management tier — it provides a web-based interface for configuring features like VLANs, QoS, port priority, and IGMP Snooping without the complexity of a fully managed switch. It's ideal for installers and IT staff who need more control than an unmanaged switch but don't require enterprise-level CLI management. Does the TL-SG1218MPE support PoE+ (802.3at)? Yes. All 16 RJ45 ports support both IEEE 802.3af (PoE, up to 15.4W) and IEEE 802.3at (PoE+, up to 30W per port), subject to the 192W total power budget shared across all ports. How many cameras can I connect? Up to 16 IP cameras can be connected via the PoE+ ports. For standard 802.3af cameras drawing around 10–12W each, the 192W budget comfortably supports a full 16-camera deployment. For higher-power PTZ or PoE+ cameras, calculate your total load to stay within the 192W budget. What are the SFP ports used for? The two SFP ports accept Gigabit fibre modules (single-mode or multi-mode) for uplink connections to a core switch or to extend your network over long distances — useful in multi-building or multi-floor installations where copper Ethernet is impractical. Can I set up VLANs on this switch? Yes. The TL-SG1218MPE supports 802.1Q VLAN configuration via its web-based Easy Smart interface, allowing you to segment camera traffic, staff devices, and guest networks onto separate logical networks for improved security and performance. Is it rack mountable? Yes. The TL-SG1218MPE is a standard 1U rack-mountable switch (440mm wide) and includes rack mounting brackets. It fits any standard 19-inch equipment rack or comms cabinet.

Read more less

TP-Link TL-SG1008MP — 8-Port Gigabit PoE+ Switch The TP-Link TL-SG1008MP is a reliable, plug-and-play 8-port Gigabit PoE+ switch designed for professional security installations, small business networks, and home office setups. With a 126W total PoE budget and support for up to 30W per port, it powers IP cameras, access points, VoIP phones, and access control devices over a single Ethernet cable — no separate power adapters required. Key Features 8 × 10/100/1000Mbps RJ45 ports, all PoE+ enabled IEEE 802.3at/af compliant — compatible with a wide range of PoE devices 126W total PoE power budget with up to 30W per port 16Gbps backplane bandwidth for smooth, uninterrupted data transfer Energy-efficient design reduces power consumption by up to 75% Store-and-forward switching with auto MDI/MDIX and auto-negotiation Desktop and rack-mountable — includes rackmount kit Plug-and-play setup — no configuration or software required Typical Use Cases CCTV & IP Camera Systems: Power and connect up to 8 PoE IP cameras from a single switch Access Control: Drive electromagnetic locks, card readers, and intercoms via PoE Wireless Networks: Power multiple Wi-Fi access points without running separate power cables Small Business & Office Networks: Reliable Gigabit connectivity for workstations, VoIP phones, and peripherals Home Networks: Expand your home network with fast, efficient switching Technical Specifications Specification Detail Ports 8 × 10/100/1000Mbps RJ45 (all PoE+) PoE Standard IEEE 802.3at / 802.3af Total PoE Budget 126W Max PoE per Port 30W Backplane Bandwidth 16Gbps MAC Address Table 4K Buffer Size 1.5Mbits Transfer Method Store-and-Forward Power Supply 100–240VAC, 50/60Hz Max Power Consumption 140.67W (with 126W PD connected) Dimensions (W × D × H) 294 × 180 × 44mm Mounting Desktop / Rack-mountable (1U) Fan 1 × internal fan Certifications FCC, CE, RoHS Network Media Cat 3/4/5 (10BASE-T), Cat 5/5e (100BASE-TX), Cat 5/5e/6+ (1000BASE-T), max 100m In the Box TL-SG1008MP, Power Cord, Installation Guide, Rackmount Kit, Rubber Feet Frequently Asked Questions Is the TL-SG1008MP managed or unmanaged? The TL-SG1008MP is an unmanaged switch. It requires no configuration — simply plug in your devices and it works straight away. There is no web interface, VLAN support, or QoS settings. Can I use non-PoE devices on this switch? Yes. All 8 ports support standard Gigabit Ethernet. Non-PoE devices such as computers, NVRs, and NAS units will connect and operate normally — the switch will not supply power to devices that don't request it. How many IP cameras can this switch power? With a 126W total PoE budget, the number of cameras depends on each camera's power draw. For example, 8 cameras drawing 15W each would use 120W — well within budget. Higher-draw cameras (e.g. PTZ at 25–30W) may reduce the total count. Is this switch rack-mountable? Yes. The TL-SG1008MP includes a rackmount kit and fits a standard 1U rack enclosure. It can also be used as a desktop unit with the included rubber feet. What is the difference between the TL-SG1008MP and the TL-SG1008PE? The TL-SG1008MP is the updated replacement model for the TL-SG1008PE. Both offer 8-port Gigabit PoE+, but the TL-SG1008MP features an improved design and is the currently supported model from TP-Link. Does this switch ship Australia-wide? Yes. CCTV Guru ships the TL-SG1008MP to all states and territories across Australia from local stock.

Read more less

TP-Link TL-SL1218MP 16-Port 10/100Mbps + 2-Port Gigabit Unmanaged PoE Switch16 PoE+ 10/100Mbps RJ45 ports, 2 Gigabit RJ45 ports and 2 combo Gigabit SFP slotsUp to 250m data and power transmission under extend mode specially designed for surveillance systemPriority mode for port1-8 to guarantees the quality of sensitive applications like video monitorHigh PoE power budget with up to 30W for each PoE port and 194W for all PoE portsEasy to use, with no configuration and installation neededHARDWARE FEATURES Interface 16 PoE+ 10/100Mbps RJ45 Ports 2 10/100/1000Mbps RJ45 Ports 2 Combo Gigabit SFP Slots Network Media 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) 100BASE-TX: UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) 1000BASE-T: UTP category 5, 5e, 6 or above cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) 1000BASE-X MMF, SMF Fan Quantity 2 Fans Physical Security Lock Yes Power Supply 100-240V AC, 50/60 Hz Backup Bandwidth 7.2 Gbps PoE+ Ports(RJ45) Standard: 802.3at/802.3af compliant PoE Ports: Port1- Port16 PoE Power Budget: 192W Mac Address Table 8K Dimensions ( W x D x H ) 17.3 × 7.1 × 1.7 in. (440 × 180 × 44 mm) Max Power Consumption 18.7 W (no PD connected) 217.2 W (with 192W PD connected) Max Heat Dissipation 63.9 BTU/h (no PD connected) 741.2 BTU/h (with 192W PD connected) SOFTWARE FEATURES Advanced Features Compatible with IEEE 802.3at/af compliant devices Port Priority Mode Extend Mode (Up to 250m PoE power supply and data transmission) Mac Address Auto-Learning And Auto-Aging IEEE802.3x Flow Control Transmission Method Store-And-Forward

Read more less

The TP-Link TL-SG116 is a high-performance 16-Port Gigabit Unmanaged Switch designed to provide an easy and reliable way to expand your wired network. Whether you are connecting multiple IP cameras, upgrading your home office, or building out a small business network, the TL-SG116 delivers Gigabit speeds without the need for complex configuration. Key Performance Features 16 Gigabit Ports: Every port provides high-speed data transfer, ideal for bandwidth-intensive devices like 4K NVRs, servers, and gaming consoles. Massive Capacity: Boasts a 32Gbps switching capacity and a 23.81Mpps forwarding rate to ensure zero bottlenecks in your network traffic. Robust Hardware: Features an 8K MAC address table and a 4.1Mb buffer for smooth data handling across all connected devices. Silent & Durable: The fanless metal casing ensures silent operation, making it perfect for noise-sensitive environments like bedrooms or offices. Why Choose the TL-SG116? Plug-and-Play: No software or configuration required. Simply plug in your cables and you're ready to go. Versatile Mounting: The compact design supports both desktop placement and wall-mounting for flexible cable management. Green Technology: Automatically adjusts power consumption according to link status and cable length to reduce your carbon footprint. Traffic Optimization: Supports 802.1p/DSCP QoS and IGMP Snooping for smooth latency-sensitive traffic like voice and video. Technical Specifications Feature Specification Number of Ports 16 × 10/100/1000Mbps RJ45 Ports Switching Capacity 32 Gbps Packet Forwarding Rate 23.81 Mpps MAC Address Table 8K Packet Buffer Memory 4.1 Mb Casing Material Durable Steel Mounting Options Desktop / Wall-Mount Fan Quantity Fanless (Silent) Standard & Protocols IEEE 802.3i/u/ab/x, 802.1p

Read more less

TP-Link TL-SG116E – 16-Port Gigabit Easy Smart Switch The TP-Link TL-SG116E bridges the gap between a basic unmanaged switch and a full managed switch. Sixteen Gigabit ports, a fanless silent design, and a metal enclosure make it a solid foundation for small business, surveillance, and home lab networks — while web-based management and a downloadable utility unlock L2 features including VLANs, QoS, IGMP snooping, port mirroring, and loop prevention, without the complexity or cost of a fully managed switch. Key Features 16 × Gigabit RJ45 Ports: Full 10/100/1000Mbps auto-negotiation on all ports with Auto MDI/MDIX — no crossover cables required. Easy Smart Management: Web UI and downloadable utility provide access to L2 features without requiring CLI or complex managed switch configuration. VLAN Support: Up to 32 active VLANs simultaneously (from a 4K VLAN ID pool) via MTU, Port-based, or 802.1Q Tag VLAN for network segmentation. QoS — 4 Priority Queues: Port-based, 802.1p, and DSCP priority with rate limiting and storm control for traffic management. IGMP Snooping V1/V2/V3: Optimises multicast traffic — essential for IP camera streams and IPTV deployments. Static Link Aggregation: Bond multiple ports for increased bandwidth between switches or servers. Port Mirroring: Mirror traffic from one port to another for network monitoring and troubleshooting. Loop Prevention: Automatically detects and prevents network loops without requiring STP configuration. Cable Diagnostics: Built-in tool to test and diagnose Ethernet cable faults from the management interface. Fanless Silent Operation: No moving parts — completely silent, suitable for offices, reception areas, and noise-sensitive environments. Durable Metal Casing: Professional-grade metal enclosure for long-term reliability in commercial installations. Green Technology: Automatically adjusts power consumption based on cable length and link status to reduce energy use. Ideal Use Cases Small business networks requiring VLAN segmentation between staff, guest, and IoT/camera traffic without a full managed switch. IP camera and NVR installations where IGMP snooping optimises multicast video streams across the network. Home lab and prosumer environments needing L2 features at an accessible price point. Silent office or reception deployments where fan noise is unacceptable. Desktop or wall-mounted installations requiring a compact, metal-cased 16-port switch. Network upgrades from basic unmanaged switches where VLAN and QoS control is now required. Technical Specifications Specification Detail Model TL-SG116E Ports 16 × 10/100/1000Mbps RJ45 (Auto MDI/MDIX) Standards IEEE 802.3i, 802.3u, 802.3ab, 802.3x, 802.1q, 802.1p Switching Capacity 32Gbps Packet Forwarding Rate 23.81Mpps MAC Address Table 8K Packet Buffer Memory 4.1Mb Jumbo Frame 9KB VLAN Up to 32 active VLANs (4K VLAN IDs); MTU / Port / 802.1Q Tag VLAN QoS Port-based / 802.1p / DSCP; 4 priority queues; rate limiting; storm control IGMP Snooping V1 / V2 / V3 Link Aggregation Static (up to 4 groups, 4 ports per group) Port Mirroring Yes Loop Prevention Yes Cable Diagnostics Yes Transmission Method Store-and-Forward Management Web UI & downloadable utility Fan Fanless (silent) Power Supply External adapter (9VDC / 0.6A) Power Consumption (Max) 9.27W @ 220V/50Hz Mounting Desktop / Wall Dimensions 286 × 111.7 × 25.4 mm Enclosure Metal Warranty 5 Years SKU TL-SG116E Barcode (EAN) 1210002617000 Frequently Asked Questions What is the difference between the TL-SG116E and a standard unmanaged switch? Unlike a basic unmanaged switch, the TL-SG116E provides web-based management and a downloadable utility that unlock L2 features including VLANs, QoS, IGMP snooping, port mirroring, loop prevention, and cable diagnostics. It offers meaningful network control without the cost or complexity of a fully managed switch. Does the TL-SG116E support PoE? No. The TL-SG116E does not support Power over Ethernet. If you need PoE for IP cameras, access points, or VoIP phones, consider the TP-Link TL-SG116P, which provides PoE+ on all 16 ports with a 120W budget. How many VLANs can I configure? The TL-SG116E supports up to 32 active VLANs simultaneously, drawn from a pool of 4096 VLAN IDs. VLANs can be configured as MTU, Port-based, or 802.1Q Tag VLANs via the web interface. Is it completely silent? Yes. The TL-SG116E is fanless with no moving parts, making it completely silent in operation. It’s well-suited for offices, reception areas, classrooms, and any environment where fan noise is undesirable. Can it be wall-mounted? Yes. The TL-SG116E supports both desktop and wall-mounting. Wall-mount hardware is included in the box. Is IGMP snooping useful for IP camera networks? Yes. IGMP snooping prevents multicast video streams from being flooded to all ports on the switch, directing camera streams only to the ports that have requested them. This reduces unnecessary traffic and improves overall network performance in surveillance deployments. What warranty does the TL-SG116E carry? The TL-SG116E is backed by a 5-year warranty.

Read more less

Power and Connect Up to 4 PoE Devices with a Single Cable The TP-Link TL-SF1005P is a compact, plug-and-play unmanaged switch with four 802.3af PoE ports and a generous 58W total power budget. It eliminates the need for separate power adapters by delivering both data and power over a single Ethernet cable — making it a practical choice for small CCTV installations, wireless access point deployments, and VoIP phone setups in homes, small offices, and retail environments across Australia. Key Features 4× PoE Ports (802.3af): Power IP cameras, access points, VoIP phones, and other 802.3af-compliant devices without separate power adapters or injectors. 58W Total PoE Budget: Up to 15.4W per PoE port, with a combined budget of 58W across all four ports — higher than many comparable desktop switches. 5× 10/100Mbps RJ45 Ports: Four PoE-enabled ports plus one uplink port for connecting to your router or network. Plug & Play: No configuration, software, or management interface required — connect and it works immediately. Fanless & Silent: Completely silent operation — suitable for desks, reception areas, and home installations. Auto-Negotiation & Auto MDI/MDIX: Automatically adjusts to connected devices and cable types for hassle-free setup. Overload Protection: Automatically manages power distribution to prevent overloading connected PoE devices. Compact Form Factor: Small desktop footprint (99.8 × 98 × 25mm) fits easily on a desk, shelf, or inside a cabinet. Common Use Cases Powering 1–4 IP security cameras in small CCTV systems Connecting and powering wireless access points in small offices or retail stores VoIP phone deployments in reception areas or small teams Expanding a home or office network to locations without nearby power outlets Replacing a PoE injector with a multi-port solution for cleaner cable management Technical Specifications Model TL-SF1005P Total Ports 5× 10/100Mbps RJ45 PoE Ports 4× (Ports 1–4), IEEE 802.3af Max PoE Per Port 15.4W Total PoE Budget 58W Switching Capacity 1 Gbps MAC Address Table 2K Transmission Method Store-and-Forward Power Supply External adapter — 48V DC / 1.25A Max Power Consumption 1.70W (no PD) / 63.51W (full PoE load) Fan Fanless (silent) Dimensions (W × D × H) 99.8 × 98 × 25mm Cable Type Cat3/4/5 (10BASE-T), Cat5/5e (100BASE-TX), max 100m Operating Temperature 0°C to 40°C Certifications CE, RoHS, FCC In the Box TL-SF1005P, Power Adapter, Installation Guide Frequently Asked Questions What is the difference between the TL-SF1005P and the TL-SF1005LP? The TL-SF1005P has a higher total PoE budget of 58W compared to the TL-SF1005LP's 41W. The TL-SF1005P also lacks the Extend Mode (250m) and Priority Mode features found on the TL-SF1005LP. If you need longer cable runs, choose the TL-SF1005LP; if you need more total PoE power, choose the TL-SF1005P. Is the TL-SF1005P managed or unmanaged? It is an unmanaged switch. There is no web interface, app, or software — it operates automatically with no configuration required. Simply plug in your devices and it works. Can I use it with 802.3at (PoE+) devices? The TL-SF1005P supports IEEE 802.3af only, providing up to 15.4W per port. It is not compatible with 802.3at PoE+ devices that require more than 15.4W. For PoE+ devices, consider a TP-Link PoE+ switch. How many IP cameras can I connect? Up to 4 IP cameras can be connected via the PoE ports (Ports 1–4). The fifth port is a standard uplink port for connecting to your router or NVR. Ensure the total power draw of all connected cameras does not exceed 58W. Does it support VLAN or QoS? No. As an unmanaged switch, it does not support VLAN, QoS, or any advanced traffic management. It is designed for simple plug-and-play deployments. What cable length is supported for PoE? Standard Ethernet cable runs up to 100m are supported for both data and PoE power delivery. Unlike the TL-SF1005LP, this model does not include an Extend Mode for longer runs.

Read more less

TP-Link TL-SG1005P 5-Port Gigabit PoE Switch (4-Port PoE, 56W) Power and Connect Your Network Devices — Without the Clutter The TP-Link TL-SG1005P is a compact, plug-and-play Gigabit switch designed for small offices, home networks, and security installations. With four PoE-enabled ports delivering up to 56W total, it powers IP cameras, VoIP phones, and wireless access points directly over a single Ethernet cable — no separate power adapters required. Key Features 5 × Gigabit RJ45 ports (10/100/1000Mbps) with auto-negotiation and auto MDI/MDIX 4 × PoE ports compliant with IEEE 802.3af/at — up to 15.4W per port 56W total PoE power budget across all ports 802.1p/DSCP QoS for smooth handling of latency-sensitive traffic IGMP Snooping for efficient multicast management Fanless, silent operation — ideal for office and residential environments Plug-and-play setup — no configuration or software required Compact desktop form factor (99.8 × 98 × 25 mm) Typical Use Cases IP Camera Systems: Power and connect up to 4 PoE IP cameras from a single switch — perfect for small CCTV installations. VoIP Phones: Deliver power and data to desk phones without additional power supplies. Wireless Access Points: Extend Wi-Fi coverage by powering PoE-capable APs directly. Small Office Networks: Expand wired connectivity for workstations, printers, and NAS devices. Home Networks: Tidy up your home setup with a single cable run to each device. Technical Specifications Specification Detail Model TL-SG1005P Ports 5 × 10/100/1000Mbps RJ45 PoE Ports Ports 1–4 (IEEE 802.3af/at) PoE Per Port Up to 15.4W Total PoE Budget 56W Switching Capacity 10 Gbps Packet Forwarding Rate 7.44 Mpps MAC Address Table 2K Jumbo Frame 16 KB Dimensions (W × D × H) 99.8 × 98 × 25 mm Weight 0.78 kg Power Supply External adapter — 53.5 VDC / 1.31A Max Power Consumption 4.29W (no PD) / 74.24W (full PoE load) Cooling Fanless Network Media Cat 3/4/5 (10M), Cat 5/5e (100M), Cat 5/5e/6+ (1000M) — max 100m QoS 802.1p / DSCP IGMP Snooping Supported Flow Control IEEE 802.3x Barcode 6935364083212 Frequently Asked Questions How many IP cameras can the TL-SG1005P power? Up to 4 PoE-powered devices can be connected on ports 1–4. The total PoE budget is 56W, so the number of cameras depends on each camera's power draw. Most standard IP cameras consume 5–12W, allowing you to run 4 cameras simultaneously with headroom to spare. Does this switch require any configuration? No. The TL-SG1005P is fully plug-and-play. Simply connect your devices and power on — no software, login, or setup is needed. Is it compatible with all PoE devices? It is compatible with IEEE 802.3af and 802.3at compliant powered devices (PDs). Always verify your device's PoE standard before connecting. Can I use it with non-PoE devices? Yes. All 5 ports support standard Gigabit data. Non-PoE devices connected to ports 1–4 will receive data only — no power will be supplied unless the device negotiates PoE. Is the TL-SG1005P suitable for outdoor use? No. This is a desktop switch designed for indoor use. For outdoor or harsh-environment installations, consider a ruggedised or weatherproof PoE switch. What is the warranty on this product in Australia? TP-Link products sold in Australia are covered by a standard manufacturer's warranty. Please refer to the TP-Link Australia warranty policy or contact us for details.

Read more less

TP-Link TL-SG1016PE 16-Port Gigabit PoE+ Switch Overview The TP-Link TL-SG1016PE is a reliable 16-port Gigabit desktop and rackmount switch designed for small-to-medium business networks and professional security installations. With 8 IEEE 802.3af/at compliant PoE+ ports and a 32Gbps backplane, it delivers both data and power over a single cable — ideal for IP cameras, access points, and VoIP phones across Australian commercial and residential sites. Key Features 16 x 10/100/1000Mbps RJ45 ports with Auto Negotiation and Auto MDI/MDIX 8 x PoE+ ports (IEEE 802.3af/at) — power IP cameras, APs, and VoIP devices without separate power adapters 32Gbps non-blocking backplane bandwidth for high-throughput environments 8K MAC address table with auto-learning and auto-aging Store-and-forward switching for reliable, error-free data transfer IEEE 802.3x flow control (full-duplex) and backpressure (half-duplex) Energy-efficient design — reduces power output by up to 75% on inactive ports Plug-and-play — no software configuration required Desktop or 1U rackmount installation flexibility Includes rackmount kit and rubber feet Use Cases CCTV & IP Camera Systems: Power and connect up to 8 PoE IP cameras directly from a single switch — no separate injectors needed. Small Business Networks: Expand office connectivity with Gigabit speeds across all 16 ports. Wireless Access Points: Deploy PoE-powered APs throughout a building without running additional power cabling. VoIP Deployments: Connect PoE-compatible IP phones alongside standard network devices on the same switch. Retail & Hospitality: Centralise network and power distribution in a compact 1U rackmount form factor. Specifications Specification Detail Total Ports 16 x 10/100/1000Mbps RJ45 PoE+ Ports 8 (IEEE 802.3af/at) Backplane Bandwidth 32 Gbps MAC Address Table 8K Buffer Size 1.5 Mbits Transfer Method Store-and-Forward Power Supply 100–240VAC, 50/60Hz Max Power Consumption (PoE on) 124.4W (220V/50Hz) Max Power Consumption (PoE off) 14.4W (220V/50Hz) Fan 1 x internal fan Dimensions (W × D × H) 294 × 180 × 44 mm Operating Temperature 0°C – 40°C Storage Temperature -40°C – 70°C Operating Humidity 10% – 90% (non-condensing) Certifications FCC, CE, RoHS SKU TL-SG1016PE Mounting Desktop / 1U Rackmount In the Box TL-SG1016PE Switch Power cord Rackmount kit Rubber feet Installation guide Frequently Asked Questions How many PoE devices can I connect to the TL-SG1016PE? Up to 8 PoE or PoE+ devices can be powered simultaneously via the dedicated PoE+ ports. The total PoE power budget is 110W, so ensure the combined power draw of connected devices does not exceed this limit. Does this switch require any software configuration? No. The TL-SG1016PE is a plug-and-play unmanaged switch. Simply connect your devices and cables — no login, software, or configuration is required. Can I rackmount this switch? Yes. The package includes a rackmount kit for standard 1U rack installation, as well as rubber feet for desktop use. Is this switch compatible with all PoE IP cameras? It is compatible with any IEEE 802.3af or 802.3at compliant PoE device, which covers the vast majority of IP cameras, wireless access points, and VoIP phones available in Australia. What cable type is required? For Gigabit speeds, use Cat 5e, Cat 6, or above UTP/STP cable up to 100 metres per run. Cat 3 or Cat 5 cable is sufficient for 10/100Mbps connections.

Read more less

Next-Generation Wi-Fi 6 Speed for the Whole Home The TP-Link Archer AX55 brings Wi-Fi 6 (802.11ax) technology to Australian homes, delivering combined speeds of up to 3000Mbps across dual bands. With OFDMA for handling more devices simultaneously, Beamforming for targeted signal strength, and OneMesh compatibility for seamless whole-home coverage, it's built for households that stream, game, video call, and connect dozens of smart devices — all at the same time. Key Features AX3000 Wi-Fi 6 Speeds: 2402Mbps on 5GHz (HE160) and 574Mbps on 2.4GHz — significantly faster than Wi-Fi 5 for 4K streaming, gaming, and large file transfers. OFDMA Technology: Increases network capacity by up to 4×, enabling simultaneous data transmission to multiple devices without congestion. Ultra-Low Latency: Up to 75% reduction in latency compared to Wi-Fi 5 — ideal for online gaming, video conferencing, and real-time applications. 4× High-Gain External Antennas with Beamforming: Concentrates Wi-Fi signal towards connected devices to extend range and improve reliability throughout 3-bedroom homes. OneMesh Compatible: Pair with a TP-Link OneMesh range extender to create a seamless, single-network mesh system with automatic roaming between nodes. Intel Home Wi-Fi Chipset: Delivers superior processing performance for consistent Wi-Fi 6 speeds under heavy multi-device load. Target Wake Time (TWT): Reduces battery drain on connected Wi-Fi devices such as smartphones, laptops, and smart home sensors. TP-Link HomeShield Security: Built-in network security with real-time threat detection, parental controls, and IoT device protection via the Tether app. DFS Support: Accesses additional 5GHz channels to reduce interference in congested Wi-Fi environments. Alexa Compatible: Control your router with Amazon Alexa voice commands for hands-free network management. Common Use Cases High-speed home internet for 3-bedroom houses with 20+ connected devices 4K and 8K video streaming on multiple TVs and devices simultaneously Low-latency online gaming on consoles and PCs Video conferencing and remote work with stable, fast connections Smart home hubs with many IoT devices (cameras, sensors, speakers) Extending coverage with OneMesh range extenders for larger homes Technical Specifications Model Archer AX55 Wi-Fi Standard Wi-Fi 6 (IEEE 802.11ax/ac/n/a/b/g) Wi-Fi Speed AX3000: 5GHz 2402Mbps + 2.4GHz 574Mbps 5GHz Band 2402Mbps (802.11ax, HE160) 2.4GHz Band 574Mbps (802.11ax) Antennas 4× fixed high-gain external antennas Streams 4 (2+2) Chipset Intel Home Wi-Fi WAN Port 1× Gigabit LAN Ports 4× Gigabit USB Port 1× USB 3.0 Working Modes Router Mode, Access Point Mode Key Technologies OFDMA, MU-MIMO, Beamforming, DFS, TWT, Airtime Fairness Mesh OneMesh compatible Security WPA3, WPA2, TP-Link HomeShield Voice Control Amazon Alexa App Management TP-Link Tether (iOS & Android) Coverage Up to 3-bedroom homes Power Supply 12V DC / 2A (external adapter) Frequently Asked Questions What is Wi-Fi 6 and do I need it? Wi-Fi 6 (802.11ax) is the latest Wi-Fi standard, offering faster speeds, lower latency, and better performance in homes with many connected devices compared to Wi-Fi 5 (802.11ac). If you have 10 or more devices, stream 4K video, game online, or work from home, Wi-Fi 6 will deliver a noticeably better experience. Is the Archer AX55 compatible with my existing devices? Yes. The Archer AX55 is fully backwards compatible with Wi-Fi 5 (802.11ac), Wi-Fi 4 (802.11n), and older Wi-Fi standards. All your existing devices will connect and work normally, with Wi-Fi 6 devices benefiting from the improved speeds and efficiency. What is OneMesh and how does it work? OneMesh is TP-Link's mesh Wi-Fi system. By pairing the Archer AX55 with a compatible TP-Link OneMesh range extender, you create a single unified network with one SSID. Your devices automatically roam to the strongest signal as you move around your home, eliminating dead zones and connection drops. Does it work with the NBN? Yes. The Archer AX55 is compatible with all NBN connection types including FTTP, FTTC, FTTN, FTTB, and HFC. For FTTP and HFC connections, you connect the router directly to the NBN connection box. For FTTN and FTTB, you'll need a modem router or a separate VDSL modem. What is TP-Link HomeShield? HomeShield is TP-Link's built-in network security suite, providing real-time threat detection, malicious site blocking, parental controls with content filtering, and IoT device protection. Basic HomeShield features are free; advanced features require a HomeShield Pro subscription. Can I manage the router remotely? Yes. The free TP-Link Tether app (iOS and Android) allows you to manage your router from anywhere — view connected devices, set parental controls, run speed tests, and reboot the router remotely.

Read more less

TP-Link TL-SF1016 16-Port 10/100Mbps Rackmount Network Switch The TP-Link TL-SF1016 is a compact, fanless 16-port Fast Ethernet rackmount switch designed for small businesses, server rooms, and network infrastructure deployments across Australia. With 16 × 10/100Mbps RJ45 ports, auto MDI/MDIX on every port, and energy-efficient technology that reduces power consumption by up to 75%, it delivers reliable, low-maintenance network connectivity in a standard 19-inch 1U rack form factor — at an accessible price point. Key Features 16 × 10/100Mbps RJ45 Ports — Connects up to 16 wired devices simultaneously at Fast Ethernet speeds, suitable for office networks, IP cameras, VoIP phones, and access points. Plug & Play — No configuration, software, or management interface required — connect and the switch operates immediately. Auto MDI/MDIX on All Ports — Automatically detects and adjusts for straight-through or crossover cables, eliminating cable type concerns during installation. Fanless & Silent Operation — No moving parts means completely silent operation — ideal for office environments, comms rooms, and noise-sensitive installations. Energy-Efficient Technology — Reduces power consumption by up to 75% by detecting cable length and link status, and adjusting power output accordingly. Standard 19-Inch 1U Rackmount — Fits any standard 19-inch rack or cabinet; rackmount kit included in the box. Store-and-Forward Switching — Checks each packet for errors before forwarding, improving network reliability and reducing error propagation. 8K MAC Address Table — Supports up to 8,000 MAC address entries for efficient packet forwarding in larger network environments. Steel Enclosure — Robust all-metal construction for durability in rack and cabinet deployments. Use Cases Small business server rooms and comms cabinets requiring a cost-effective 16-port Fast Ethernet switch IP camera and NVR installations where 100Mbps per port is sufficient for camera bandwidth requirements Office networks connecting desktop PCs, VoIP phones, and access points to a central switch Expanding an existing network with additional ports without replacing the core infrastructure Education facilities, strata buildings, and small warehouses needing a simple, unmanaged rackmount switch Technical Specifications Specification Detail Model TL-SF1016 Ports 16 × 10/100Mbps RJ45 (Auto Negotiation, Auto MDI/MDIX) Standards IEEE 802.3i, IEEE 802.3u, IEEE 802.3x Switching Capacity 3.2Gbps Packet Forwarding Rate 2.38Mpps MAC Address Table 8K Buffer Memory 2MB Transfer Method Store-and-Forward Network Media 10BASE-T: Cat3/4/5 UTP (max 100m); 100BASE-TX: Cat5/5e or above (max 100m) Fan Fanless (silent operation) Power Supply 100–240V AC, 50/60Hz Max Power Consumption 2.23W (220V/50Hz) Energy Saving Up to 75% power reduction via cable length & link detection Form Factor 19-inch 1U Rackmount Dimensions 440 × 180 × 44 mm Operating Temperature 0°C to 40°C Certifications FCC, CE, RoHS In the Box Switch, power cord, rackmount kit, rubber feet, installation guide Warranty 2 Years Recommended Accessories TP-Link TL-POE260S 2.5G PoE+ Injector — Add PoE power to individual ports on this non-PoE switch for powering IP cameras or access points via a single cable. TP-Link TL-SM331T RJ45 SFP Module — If your core switch has an SFP uplink slot, use this copper SFP module to connect the TL-SF1016 via a standard Cat6 cable. Cat6 Ethernet Cable — Recommended for reliable 100Mbps connections at the full 100m distance across all 16 ports. 19-Inch Network Rack or Wall Cabinet — Required for rackmount installation; the TL-SF1016 fits any standard 19-inch 1U rack space. Frequently Asked Questions Is the TL-SF1016 a managed or unmanaged switch? The TL-SF1016 is an unmanaged switch. It requires no configuration, login, or management interface — simply connect your devices and it operates automatically. If you need VLANs, QoS, or port monitoring, consider TP-Link’s JetStream managed switch range. Does this switch support PoE? No. The TL-SF1016 does not provide Power over Ethernet. If you need to power IP cameras, access points, or VoIP phones via Ethernet, use a TP-Link PoE switch (such as the TL-SG108PE) or add a PoE injector (such as the TL-POE260S) to individual ports. Is 100Mbps per port sufficient for IP cameras? Yes, for most IP camera deployments. A typical 4MP or 8MP IP camera streams at 4–8Mbps, well within the 100Mbps capacity of each port. For high-density NVR systems with many high-bitrate cameras on a single uplink, a Gigabit switch may be more appropriate. Can I use Cat5e cable with this switch? Yes. The TL-SF1016 supports Cat5, Cat5e, and Cat6 UTP cable for 100BASE-TX operation at up to 100 metres. Cat5e or Cat6 is recommended for new installations. How loud is the switch in operation? The TL-SF1016 is completely fanless, meaning it produces no noise during operation. This makes it suitable for office environments, meeting rooms, and any installation where fan noise would be disruptive. Does the rackmount kit come included? Yes. The box includes the switch, power cord, rackmount kit (brackets and screws), rubber feet for desktop use, and an installation guide. No additional hardware is required for standard 19-inch rack installation.

Read more less

4-Port PoE with Smart Management in a Compact Gigabit Desktop Switch The TP-Link TL-SG108PE is an 8-port Gigabit Easy Smart switch that combines PoE power delivery with essential Layer 2 management features — VLAN, QoS, IGMP Snooping, and Port Mirroring — in a compact, fanless desktop form factor. With four 802.3af PoE ports and a 55W total budget, it powers IP cameras, access points, and VoIP phones while giving you the traffic control needed for a secure, well-organised small business or surveillance network. Managed via a web browser or the Easy Smart Configuration Utility, no advanced networking expertise is required. Key Features 4× PoE Ports (802.3af, Ports 1–4): Power IP cameras, wireless access points, VoIP phones, and other 802.3af-compliant devices at up to 15.4W per port via a single Ethernet cable. 55W Total PoE Budget: Supports up to four simultaneously powered PoE devices — sufficient for most small CCTV and Wi-Fi deployments. 8× Gigabit RJ45 Ports: Full 10/100/1000Mbps auto-negotiation on all ports for fast wired connectivity across all connected devices. VLAN Support (Port-based, 802.1Q, MTU): Segment camera traffic, staff devices, and guest networks onto separate logical networks for improved security and performance. QoS (Port-based & 802.1p): Prioritises latency-sensitive traffic such as IP camera streams and VoIP calls to ensure consistent performance under load. IGMP Snooping: Optimises multicast traffic for IP camera streams and IPTV, reducing unnecessary bandwidth consumption across the network. Port Mirroring: Mirror traffic from one port to another for network monitoring, diagnostics, and troubleshooting without disrupting live traffic. Web-Based Management: Configure and monitor via a web browser or the Easy Smart Configuration Utility — no CLI or advanced networking knowledge required. Fanless & Silent: Completely silent operation — suitable for offices, reception areas, and home installations. Plug & Play: Works out of the box for basic switching without any configuration — smart features are available when needed. Common Use Cases Powering and managing up to 4 IP cameras in small CCTV installations with VLAN isolation Connecting and powering Wi-Fi access points via PoE with guest VLAN separation Small business networks requiring both PoE and basic traffic management in one device VoIP phone deployments needing PoE power and QoS prioritisation for call quality Upgrading from an unmanaged PoE switch to gain VLAN and QoS control Technical Specifications Model TL-SG108PE Total Ports 8× 10/100/1000Mbps RJ45 PoE Ports 4× (Ports 1–4), IEEE 802.3af Max PoE Per Port 15.4W (802.3af) Total PoE Budget 55W Switching Capacity 16 Gbps Packet Forwarding Rate 11.9 Mpps MAC Address Table 4K Packet Buffer Memory 1.5 Mbit VLAN Port-based, 802.1Q Tag VLAN, MTU VLAN QoS Port-based & 802.1p tag-based IGMP Snooping Yes Port Mirroring Yes Flow Control IEEE 802.3x Management Web UI, Easy Smart Configuration Utility Fan Fanless (silent) Power Supply External adapter — 48V DC / 1.25A Max Power Consumption 5.2W (no PD) / 65.2W (full PoE load) Form Factor Desktop Weight 840g Frequently Asked Questions What is the difference between the TL-SG108PE and the TL-SG1008P? Both are 8-port Gigabit switches with 4 PoE ports. The TL-SG1008P is fully unmanaged — plug-and-play with no configuration options. The TL-SG108PE adds web-based management with VLAN, QoS, IGMP Snooping, and Port Mirroring, making it significantly more capable for business and surveillance networks that require traffic control and segmentation. Does the TL-SG108PE support PoE+ (802.3at)? No. The TL-SG108PE supports IEEE 802.3af (PoE) only, providing up to 15.4W per port. It does not support 802.3at (PoE+). Ensure your powered devices are 802.3af-compliant before purchasing. For PoE+ devices requiring up to 30W, consider the TL-SG1210MP or TL-SF1009P. How many PoE devices can I connect? Up to 4 PoE devices can be connected via ports 1–4. The total shared PoE budget is 55W. For example, four cameras drawing 12W each would use 48W — within the 55W budget. Ports 5–8 are standard Gigabit ports with no PoE capability. Is it suitable for IP camera and CCTV networks? Yes. The TL-SG108PE powers up to four 802.3af IP cameras directly via PoE, and VLAN support lets you isolate camera traffic from your main network for improved security. IGMP Snooping also helps manage multicast video streams efficiently. What is an Easy Smart switch? Easy Smart is TP-Link's simplified management tier — it provides a web-based interface for configuring VLANs, QoS, IGMP Snooping, and Port Mirroring without the complexity of a fully managed switch. It's ideal for small business owners and installers who need more control than an unmanaged switch but don't require enterprise-level CLI management. Can I use it without any configuration? Yes. The TL-SG108PE works as a standard plug-and-play switch out of the box — all devices connected will communicate normally without any setup. Smart features such as VLAN and QoS are only applied when you choose to configure them via the web interface.

Read more less

Next-Generation Wi-Fi 6 Speed and Coverage for the Whole HomeThe TP-Link Archer AX72 is an AX5400 dual-band Wi-Fi 6 router built for households that demand fast, reliable wireless connectivity across multiple devices. With combined speeds of up to 5400 Mbps, support for 200+ simultaneous connections, and TP-Link HomeShield security, the AX72 is a significant upgrade for any home or small office network on NBN or fibre.Key Features AX5400 Wi-Fi 6 — 4804 Mbps on 5 GHz (HE160) + 574 Mbps on 2.4 GHz for combined speeds up to 5400 Mbps 4T4R + HE160 — top-tier Wi-Fi 6 structure for maximum 5 GHz throughput and range MU-MIMO & OFDMA — simultaneously serves multiple devices, reducing congestion and quadrupling average throughput Connect 200+ Devices — ideal for smart homes with many concurrent Wi-Fi clients 6× Fixed High-Performance Antennas — with Beamforming to concentrate signal towards connected devices HomeShield Security — TP-Link’s premium network and IoT protection suite, including parental controls and real-time threat detection 1× USB 3.0 Port — share storage devices or build a private cloud across your network DFS Support — accesses additional 5 GHz channels to reduce wireless congestion Easy Setup — configure in minutes via the TP-Link Tether app Typical Use Cases High-speed NBN or fibre home networking for 3-bedroom houses and larger 4K/8K streaming and online gaming with low latency Smart home hubs managing 50+ IoT devices simultaneously Home offices requiring fast, stable Wi-Fi for video conferencing and large file transfers USB network-attached storage (NAS) for media sharing across the home Technical Specifications Specification Detail Model Archer AX72 Wi-Fi Standard Wi-Fi 6 (IEEE 802.11ax/ac/n/a 5GHz, 802.11ax/n/b/g 2.4GHz) Wi-Fi Speed AX5400: 4804 Mbps (5GHz, HE160) + 574 Mbps (2.4GHz) Antennas 6× Fixed High-Performance External Antennas MIMO 4×4 MU-MIMO OFDMA Supported (2.4GHz & 5GHz) WAN Port 1× Gigabit WAN LAN Ports 4× Gigabit LAN USB 1× USB 3.0 Operating Modes Router Mode, Access Point Mode Security WPA/WPA2/WPA3, HomeShield, SPI Firewall, Guest Network Management TP-Link Tether App, Web Interface Certifications CE, FCC, RoHS Warranty 3 Years Frequently Asked Questions Is the Archer AX72 compatible with Australian NBN connections? Yes. The AX72 supports PPPoE, Dynamic IP, and Static IP WAN types, covering all NBN connection methods including FTTP, FTTC, FTTN, and HFC. Connect it directly to your NBN modem or gateway via the Gigabit WAN port. What is the difference between Wi-Fi 6 and Wi-Fi 5 (AC)? Wi-Fi 6 (802.11ax) delivers faster speeds, lower latency, and significantly better performance in environments with many connected devices compared to Wi-Fi 5 (802.11ac). Technologies like OFDMA and MU-MIMO allow the AX72 to serve multiple devices simultaneously rather than sequentially. Do I need Wi-Fi 6 devices to benefit from the Archer AX72? No. The AX72 is backwards compatible with Wi-Fi 5, Wi-Fi 4, and older devices. However, the full speed and efficiency benefits of Wi-Fi 6 are only realised when connecting Wi-Fi 6-capable devices. What is HomeShield and is it free? HomeShield is TP-Link’s network security platform offering parental controls, IoT device protection, and real-time threat detection. Basic features are free; advanced features require a HomeShield Pro subscription. Can I use the USB 3.0 port for network storage? Yes. You can connect a USB hard drive or flash drive to the USB 3.0 port and share it across your network as a basic NAS (Network Attached Storage) device, accessible via the Tether app or web interface.

Read more less