Dahua 4-Port PoE Switch (Unmanaged) DH-PFS3106-4ET-60-V2 Dahua 4 Port POE Switch (unmanaged) Eight-Pin assignment PoE power supply Intelligent PoE Hi-PoE 60W (Orange Port) PoE watchdog 250 m long distance PoE transmission Wide operating temperature: -30C to +65C (-22F to +149F) Specifications POE SWITCH ETHERNET PORT 4 OPTICAL PORT 1 UPLINK PORT 1 POE BUDGET Port 1<=60 W (Hi-PoE), port 2-4<=30 W, total<=60 W LAYER Layer 2 TYPE Unmanaged Downloads Datasheet of DH-PFS3106-4ET-60 user manual

Read more less

Dahua 10-Port Unmanaged Desktop Switch with 8 Port PoE DH-PFS3110-8ET-96-V2 The Dahua 10-Port Unmanaged Desktop Switch with 8 Port PoE allows for long distance transmission of power and data, while the intelligent PoE ensures efficient power supply to connected devices. With a wide operating temperature range and PoE watchdog, this switch is a reliable and adaptable solution for powering your devices. Features Eight-PIN Assignment PoE Power Supply Intelligent PoE Red port supports 90W IEEE802.3bt PoE watchdog 250 m long distance PoE transmission Wide operating temperature: -30C to +65C (-22F to +149F) Specifications ETHERNET PORT 8 OPTICAL PORT 1 UPLINK PORT 1 POE BUDGET Port1<=60W, Port2-8<=30W, Total<=96W LAYER Layer 2 TYPE Unmanaged Downloads Datasheet of DH-PFS3110-8ET-96User Manual

Read more less

An 8-port, Layer 2 PoE switch supporting silent fanless cooling.Features: (4) GbE, PoE+ RJ45 ports (4) GbE RJ45 ports 52W total PoE supply* Wall-mountable (kit included) Managed with the UniFi Network application: Version 7.2.94 and later *With an external 60W power adapter. Technical Specifications Mechanical Dimensions 99.6 x 163.7 x 31.7 mm (4 x 6.4 x 1.3") Weight 295 g (10.4 oz) Enclosure material Polycarbonate Hardware Management interface Ethernet In-Band Networking interface (8) GbE RJ45 ports PoE interface (4) PoE/PoE+ (Pins 1, 2+; 3, 6-) Total non-blocking throughput 8 Gbps Switching capacity 16 Gbps Power method 54V DC, 1.1A power adapter Power supply 54V, external, 60W Supported voltage range 50—57V DC Max. power consumption 8W (Excluding PoE output) Total available PoE 52W**With an external 60W power adapter. Max. PoE wattage per port by PSE PoE+: 30W Button Factory reset Ambient operating temperature -15 to 40° C (5 to 104° F) Ambient operating humidity 10 to 90% noncondensing Certifications CE, FCC, IC Switching Features Layer 2 features IGMP snoopingSTP / RSTP with priorities and port-level disablePort isolationStorm controlVoice VLANPort mirroringLACP port aggregationMulticast / broadcast rate limitingMAC address blockingFlow control802.1X controlJumbo framesProprietary loop protectionDHCP snooping / guardingEgress rate limitLLDP-MEDPort restricted by MACDevice isolation with ACLs Layer 3 features – LEDs System Status Ethernet PoESpeed/link/activity PoE Link/activity Application Requirements UniFi Network Version 7.2.94 and later Downloads DatasheetInstallation Guide

Read more less

Simple, Reliable PoE Power for Cameras and Access Points The TP-Link TL-SF1005LP is a compact, plug-and-play desktop switch that delivers both data and power over a single Ethernet cable to up to four PoE devices. With a 41W total PoE budget, Extend Mode for long cable runs up to 250m, and fanless silent operation, it's an ideal solution for small CCTV installations, IP phone deployments, and wireless access point setups in homes, small offices, and retail environments across Australia. Key Features 4× PoE Ports (802.3af): Power IP cameras, access points, VoIP phones, and other 802.3af-compliant devices without separate power adapters. 41W Total PoE Budget: Shared across all four PoE ports — sufficient for most small-scale deployments with standard PoE devices. Extend Mode (up to 250m): Push data and power up to 250 metres at 10Mbps on a single cable run — ideal for cameras positioned far from the switch. Priority Mode (Ports 1–2): Prioritises traffic on ports 1 and 2 to ensure consistent performance for latency-sensitive devices such as IP cameras or VoIP phones. Plug & Play: No configuration, software, or management interface required — simply connect and go. Fanless & Silent: Completely silent operation makes it suitable for office desks, reception areas, and home installations. Compact Desktop Form Factor: Small footprint (100 × 98 × 25mm) fits easily on a desk, shelf, or inside a cabinet. Physical Security Lock: Kensington-style lock slot for securing the unit in shared or public spaces. Common Use Cases Powering 1–4 IP security cameras in small CCTV systems Connecting and powering wireless access points in small offices or retail stores VoIP phone deployments in reception areas or small teams Extending camera cable runs beyond the standard 100m Ethernet limit Home network expansion with PoE device support Technical Specifications Model TL-SF1005LP Total Ports 5× 10/100Mbps RJ45 PoE Ports 4× (Ports 1–4), IEEE 802.3af Total PoE Budget 41W Switching Capacity 1 Gbps Packet Forwarding Rate 0.744 Mpps MAC Address Table 2K Extend Mode Range Up to 250m at 10Mbps (Ports 1–4) Priority Mode Ports 1–2 (high priority) Transmission Method Store-and-Forward Power Supply External adapter — 53.5V DC / 0.81A Max Power Consumption 1.9W (no PD) / 47W (full PoE load) Fan Fanless (silent) Physical Security Lock Yes Dimensions (W × D × H) 100 × 98 × 25mm Operating Temperature 0°C to 40°C Operating Humidity 10–90% RH (non-condensing) Certifications FCC, CE, RoHS In the Box TL-SF1005LP, Power Adapter, Installation Guide Frequently Asked Questions Is the TL-SF1005LP managed or unmanaged? It is an unmanaged switch. There is no web interface, app, or software required — it operates automatically with no configuration needed. Mode switching (Extend/Priority) is done via physical buttons on the unit. What is the maximum PoE power per port? Each PoE port supports up to 15.4W (IEEE 802.3af standard). The total shared PoE budget across all four ports is 41W, so plan your device load accordingly. Can I use it with 802.3at (PoE+) devices? The TL-SF1005LP supports 802.3af only (up to 15.4W per port). It is not compatible with 802.3at PoE+ devices that require more than 15.4W. For PoE+ devices, consider a PoE+ switch from the TP-Link range. How does Extend Mode work? Pressing the Extend Mode button reduces port speed to 10Mbps and extends the maximum cable distance from 100m to 250m on ports 1–4. This is particularly useful for IP cameras installed at the perimeter of a property. Can I power a PTZ camera with this switch? It depends on the PTZ camera's power requirement. Most compact PTZ cameras draw under 15.4W and are 802.3af compatible — check your camera's spec sheet. High-power PTZ cameras typically require 802.3at PoE+ or a dedicated power supply. Does it support VLAN or QoS? No. As an unmanaged switch, it does not support VLAN, QoS, or any advanced traffic management features. The Priority Mode button provides basic port prioritisation for ports 1–2 only.

Read more less

Hikvision Smart Managed Switch · 4 PoE · 60W The Hikvision DS-3E1105P-EI is a compact smart managed PoE switch built for smaller CCTV and networking setups that need stable power delivery, easier fault recovery, and smarter port control. With 4 Fast Ethernet PoE ports and 1 uplink RJ45 port, it is ideal for small IP camera systems, intercoms, and edge network devices. Designed for practical surveillance deployments, this switch supports PoE watchdog to auto-restart unresponsive cameras, 802.1Q VLAN, STP/RSTP loop prevention, cable detection, and up to 300 m long-range PoE transmission. It also includes 6 kV surge protection on PoE ports and a 60W total PoE budget. If you need a small Hikvision PoE switch for cameras, intercoms, or remote endpoints with better stability than a basic unmanaged switch, the DS-3E1105P-EI is a strong option. Ports 4 PoE + 1 Uplink PoE Budget 60W Total Long Range Up to 300m Protection 6 kV Surge PoE Standard 802.3af / at Smart Features VLAN + Watchdog ✔ Smart PoE switching   ✔ Ideal for CCTV cameras   ✔ Compact metal housing Best For 🎥 Small CCTV SystemsIdeal for powering and connecting up to 4 IP cameras in home or small business installations. 🏠 Homes & Small OfficesGreat for compact surveillance or networking setups where you want better stability than a basic switch. 🚪 Intercom & Access DevicesSuitable for PoE-powered intercoms, door stations, and access control endpoints. 🛠 Remote or Long Cable RunsUseful where extended PoE reach and cable diagnostics are important for reliable deployment. Technical Specifications Model DS-3E1105P-EI Ports 4 × 10/100 Mbps PoE ports, 1 × 10/100 Mbps RJ45 port MAC Address Table 2K Switching Capacity 1 Gbps Packet Forwarding Rate 0.74 Mpps Internal Cache 768 Kbits PoE Standard IEEE 802.3af / IEEE 802.3at PoE Ports Ports 1 to 4 Max Port Power 30W Total PoE Budget 60W Long Range Ports 1 to 4: up to 300m VLAN 802.1Q, VLAN ID 1–4094, max 32 VLANs Loop Prevention STP / RSTP PoE Watchdog Auto-detect and restart unresponsive cameras Surge Protection 6 kV Power Supply 54VDC, 1.2A Dimensions 121.1 × 27.6 × 83.1 mm Installation Desk-mounted / Wall-mounted Housing Metal ⚡ Explore More Security & Networking Solutions Pair this switch with Hikvision security cameras, video intercom systems, or build a complete setup with our CCTV System Builder. Build Your Security System → More information Download official Hikvision documents for specifications, setup, and product resources. Datasheet PDF Quick Start Guide Official Resource User Manual Official Resource 3 Year Australian Warranty Fast Australia-wide Delivery Genuine Australian Stock

Read more less

Uniarch switch, 10 x 100Mbps network ports, including 8 PoE/PoE+ ports, 2 x 100Mbps uplink ports, Max capacity for single port 30W, total capacity 120W, up to 250m transmission distance, all-metal housing Multiple working modes to address your business needs: Normal, Secure and Surveillance Support port traffic control Support for secure mode, all downlink ports can communicate only with uplink ports Up to 250m transmission distance on surveillance mode Support buffer optimization All-metal housing, safe and reliable Specifications POE SWITCH Ethernet Port 10 (8 x PoE Port) Optical Port 0 UpLink Port 2 PoE Budget Max capacity: 120W. Max capacity for single port: 30W Layer Layer 2 Type Unmanaged Downloads SW-2110-P Switch Datasheet-V1.01PoE Switch Quick Guide-V1.018FE(PoE)+2FE PoE Switch User Guide

Read more less

Hikvision 8 Port Fast Ethernet Unmanaged POE Switch, NS-0109P-60 Unmanaged switch with 8 x 100 Mbps PoE ports, 1 x 100 Mbps RJ45 port All ports support 6 kV lighting protection 60 W PoE power budget Maximum transmission distance is 250 meters for port 1 to 8 in "extend" mode MAC address auto learning and auto aging Downloads Datasheet Quick Start Guide Communication Matrix

Read more less

Layer 2 switch with (5) GbE RJ45 ports, including (1) 802.3af PoE input.The Switch Flex Mini (USW Flex Mini) is a fully managed, Layer 2 switch with (5) GbE RJ45 ports, including (1) 802.3af PoE input. The USW Flex Mini can be powered with either PoE (via Port 1) or its included USB-C power adapter*. This switch can also be monitored or configured from anywhere with the powerful, intuitive UniFi Network web application and mobile app.Features: (1) GbE, 802.3af PoE RJ45 input (4) GbE RJ45 ports Compact, slim housing Can be powered with a 5V, 1A USB-C adapter (Only Comes In Single Pack) Downloads Datasheet Installation Guide

Read more less

The Wi-Tek Wiking WK-PS206 is a compact 4-port 100Mbps PoE switch with 2 uplink ports, designed for cost-effective and reliable CCTV and IP device networking. Supporting a 45W PoE budget, it powers up to 4 PoE-enabled devices with IEEE 802.3af/at compliance. Equipped with smart DIP switch modes, the WK-PS206 allows 250m long-distance PoE transmission, VLAN port isolation for security, and PD Alive watchdog to automatically reboot unresponsive devices. Its fanless metal housing provides silent and durable operation, making it perfect for surveillance systems, small business networks, and hospitality environments where quiet reliability is essential. Key Features 4 × 10/100Mbps PoE Ports + 2 Uplink Ports for flexible connectivity IEEE 802.3af/at Compliant (up to 30W per port) 45W Total PoE Budget for powering multiple IP devices 250m Extend Mode for long-distance PoE transmission VLAN Mode isolates downlink ports to improve network security PD Alive Watchdog auto-reboots offline PoE devices Fanless Metal Housing ensures quiet, reliable performance Plug-and-Play Installation — no configuration required Compact Desktop/Wall-Mount Design for flexible deployment Certified Safe: CE, FCC, RoHS, UKCA, RCM Technical Specifications Brand / Model Wi-Tek Wiking WK-PS206 SKU WK-PS206 Downlink Ports 4 × 10/100 Mbps RJ45 PoE (IEEE 802.3af/at, up to 30 W per port) [oai_citation:0‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) Uplink Ports 2 × 10/100 Mbps RJ45 [oai_citation:1‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) Total PoE Budget 45 W (pins 1/2 +, 3/6 –) [oai_citation:2‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) Switching Capacity 1.2 Gbps [oai_citation:3‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) Forwarding Rate 0.89 Mpps [oai_citation:4‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) MAC Address Table 2K [oai_citation:5‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) Buffer / Jumbo Frame 768 Kbit buffer; 15 KB jumbo frame [oai_citation:6‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) Forwarding Mode Store-and-Forward [oai_citation:7‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) DIP Switch Modes Default: 100 m PoE @ 100 Mbps (VLAN & PD-Alive off). VLAN: Downlink port isolation to uplinks; PD-Alive enabled. Extend: Up to 250 m @ 10 Mbps; PD-Alive enabled. PD-Alive: Auto-reboots unresponsive PoE devices. Power Input 100–240 V AC, 50/60 Hz [oai_citation:8‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) Power Consumption Idle: 10 W; Full load (PoE + traffic): 55 W [oai_citation:9‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) Housing / Cooling Metal (iron), fanless [oai_citation:10‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) Installation Desktop / Wall-mount [oai_citation:11‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) Dimensions 160 × 90 × 35 mm (switch); 245 × 190 × 60 mm (package) [oai_citation:12‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) Weight 0.37 kg (net); 0.64 kg (package) [oai_citation:13‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) LED Indicators PWR: On = power OK Link: On = link; Blinking = activity SW: On = VLAN; Blinking = Extend; Off = Default [oai_citation:14‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) Standards IEEE 802.3, 802.3u, 802.3x; compatible with 802.3af/at [oai_citation:15‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) Operating / Storage 0–40 °C, 10–90% RH; storage –40–70 °C, 5–90% RH [oai_citation:16‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) Surge / ESD IEC 61000-4-5: CM ±4 kV, DM ±2 kV; IEC 61000-4-2: Contact ±6 kV, Air ±8 kV [oai_citation:17‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) Certifications CE, FCC, RoHS, UKCA, RCM [oai_citation:18‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) Package Contents Switch, AC power cord, Quick Installation Guide [oai_citation:19‡WK-PS206_Datasheet_V3.0_20250115.pdf](file-service://file-LTWnU5D9n4VCnTgmXP3QqS) The WK-PS206 PoE Switch is ideal for: Small CCTV Networks – power and connect up to 4 IP cameras. Retail & Office Environments – VLAN mode enhances network security. Hospitality & Hotels – silent fanless design ensures noise-free operation. Entry-Level PoE Deployments – cost-effective power for APs, IP phones, and cameras. Its compact form factor, plug-and-play setup, and PD Alive watchdog make it a reliable choice for small-scale PoE applications.

Read more less

IP-COM G1105PD 5-Port Gigabit PD Switch With 4-Port PoE Features: Five 10/100/1000 Mbps auto-negotiation ports Port 5 supports power supply by a PSE compliant with IEEE 802.3af/at Ports 1 - 4 support power supply to low-power PDs compliant with IEEE 802.3af The switch supports auto MDI/MDIX, simplifing the network structure and maintenance The non-blocking wire-speed forwarding function guarantees the smooth operation of network applications Full-duplex flow control and half-duplex back pressure control prevent frame loss caused by port blocking The switch supports the store-and-forward transfer mode and a 2 K MAC address table The switch supports 9K jumbo frame, improving the forwarding rate of large files The switch supports IP camera connection and guarantees the smoothness and clearness of monitoring videos Downloads G1105PD Datasheet G1105PD Quick Installation Guide

Read more less

The Dahua DH-CS4006-4ET-60 is a highly intuitive 6-port Layer 2 smart managed switch designed for seamless IP surveillance management. Featuring DoLynk Care cloud integration, this switch allows installers to monitor network health, view topologies, and reboot ports remotely, significantly reducing on-site maintenance costs. Power Your High-Demand Devices: Port 1 supports Hi-PoE (up to 60W), making it ideal for powering PTZ cameras or high-performance TiOC models that require more than standard PoE+. Key Features Cloud Management: Real-time monitoring and remote maintenance via the DoLynk Care app and web platform. Intelligent PoE: Supports PoE Watchdog to automatically detect and restart crashed IP cameras, ensuring 24/7 uptime. Long Distance Transmission: Extend your PoE reach up to 250 meters—perfect for large properties and long cable runs. Network Topology: Automatically generates a visual map of your connected devices for fast troubleshooting. Durable Design: Full metal casing with excellent heat dissipation and 6kV surge protection for reliable operation in Australian conditions. Detailed Technical Specifications Hardware Feature Specification Total Ports 4 x 10/100 PoE Ports + 2 x Gigabit Uplink Ports PoE Budget Total 60W (Port 1 ≤ 60W Hi-PoE; Ports 2-4 ≤ 30W PoE+) PoE Protocols IEEE802.3af; IEEE802.3at; Hi-PoE Switching Capacity 4.8 Gbps Packet Forwarding 3.57 Mpps Lightning Protection Common Mode 4kV / Differential Mode 2kV Operating Temp -10°C to +55°C Dimensions 130 mm × 90 mm × 26 mm More Information Dahua CS4006-4ET-60 Datasheet 20230807 Dahua Ethernet Switch (Cloud Managed Switch) User's Manual V1.0.0Dahua Ethernet Switch (Cloud Managed PoE Switch) Quick Start Guide V1.0.1Dahua CS4006-4ET-60 DimensionDahua CS4006-4ET-60 Port Frequently Asked Questions What is Hi-PoE?Hi-PoE provides up to 60W of power on a single port (Port 1 on this model). This is essential for high-draw devices like PTZ cameras or outdoor heaters that exceed the 30W limit of standard PoE+. Do I need a cloud subscription?Basic management through DoLynk Care is generally available for Dahua devices to provide remote health monitoring and port control.

Read more less

TP-Link TL-SG116P – 16-Port Gigabit Unmanaged Desktop Switch with 16-Port PoE+ The TP-Link TL-SG116P is a plug-and-play 16-port Gigabit desktop switch with full PoE+ on every port — no uplink-only PoE, no compromises. With a 120W total PoE budget, 30W per port, and intelligent power management built in, it’s purpose-built for IP camera installations, wireless access point deployments, and small business networks where simplicity and reliability matter. PoE Auto Recovery automatically reboots unresponsive devices, reducing the need for manual intervention on site. Key Features 16 × Gigabit PoE+ Ports: Every port delivers both data and power — no dedicated uplink ports consuming PoE budget. Supports IEEE 802.3af/at with up to 30W per port. 120W Total PoE Budget: Sufficient to simultaneously power multiple IP cameras, wireless APs, VoIP phones, and access control readers across all 16 ports with intelligent load management. PoE Auto Recovery: Automatically detects and reboots dropped or unresponsive PoE-powered devices (cameras, APs) without manual intervention — critical for unattended installations. Extend Mode — Up to 250m: Extends data and power transmission range to 250 metres over a single Cat5e/Cat6 cable, well beyond the standard 100m Ethernet limit — ideal for large properties and perimeter camera runs. Priority Mode: Ports 1–4 are assigned high priority to guarantee bandwidth and power for latency-sensitive devices such as NVRs, primary cameras, or VoIP phones. Isolation Mode: One-click client traffic separation prevents devices on the switch from communicating with each other — useful for guest networks, multi-tenant environments, and security-conscious deployments. Intelligent Power Management: When total PoE consumption approaches 120W, the switch automatically reduces power to lower-priority ports to protect higher-priority devices and prevent overload. Plug and Play: No configuration, software, or management interface required — connect and go. Durable Metal Casing: High-quality metal enclosure protects internal components and passes stringent reliability testing for long-term deployment in demanding environments. Ideal Use Cases Powering and connecting up to 16 IP cameras in a CCTV or surveillance installation without separate power supplies. Deploying multiple wireless access points across an office, warehouse, school, or retail environment from a single switch. Small business and SME networks requiring a reliable, zero-configuration Gigabit PoE switch. Dormitory, apartment, or multi-tenancy installations where Isolation Mode keeps client traffic separated. Long-distance camera runs up to 250m using Extend Mode on large properties, farms, or perimeter security systems. VoIP phone deployments where Priority Mode ensures call quality is maintained under load. Technical Specifications Specification Detail Model TL-SG116P Total Ports 16 × 10/100/1000Mbps RJ45 PoE Ports 16 × PoE+ (all ports) PoE Standard IEEE 802.3af / IEEE 802.3at (PoE+) Max PoE Per Port 30W Total PoE Budget 120W Switching Capacity 32Gbps Forwarding Rate 23.8Mpps MAC Address Table 8K Extend Mode Range Up to 250m (data & power, at reduced speed) Special Modes Extend Mode, Priority Mode, Isolation Mode PoE Auto Recovery Yes (automatic PD device reboot) Management Unmanaged (plug and play) Enclosure Metal desktop Fan Fanless Weight 2kg SKU TL-SG116P Barcode (EAN) 4895252500301 Downloads TL-SG116P Datasheet (PDF) Frequently Asked Questions Does every port on the TL-SG116P support PoE+? Yes. All 16 ports are PoE+ capable, each delivering up to 30W. There are no dedicated uplink ports that consume PoE budget without powering devices. How many IP cameras can the TL-SG116P power simultaneously? With a 120W total PoE budget, the number of cameras depends on each camera’s power draw. For example, 16 cameras drawing 7.5W each would consume exactly 120W. Most standard IP cameras draw between 5W and 15W, so real-world capacity is typically 8–16 cameras depending on the models used. What is Extend Mode and when should I use it? Extend Mode increases the maximum cable run from the standard 100m Ethernet limit to 250 metres by reducing the link speed to 10Mbps. It’s ideal for perimeter cameras, gate cameras, or any device located far from the switch on a large property. Enable it via the hardware DIP switch on the unit. What does PoE Auto Recovery do? PoE Auto Recovery periodically checks the status of connected PoE devices. If a device (such as an IP camera or wireless AP) stops responding, the switch automatically cuts and restores power to reboot it — similar to unplugging and replugging the device — without any manual intervention required. Can I use the TL-SG116P with non-PoE devices? Yes. The switch automatically detects whether a connected device is PoE-capable. Non-PoE devices (such as computers or NVRs) connect normally via Ethernet without receiving any power — there is no risk of damage to non-PoE equipment. Is the TL-SG116P managed or unmanaged? The TL-SG116P is an unmanaged switch — it requires no software, web interface, or configuration to operate. Mode settings (Extend, Priority, Isolation) are configured via physical DIP switches on the unit. If you require VLAN, QoS, or remote management, consider TP-Link’s managed PoE switch range. Is it fanless? Yes. The TL-SG116P operates silently without a cooling fan, making it suitable for quiet environments such as offices, reception areas, and meeting rooms.

Read more less

TP-Link TL-SG1210P – 10-Port Gigabit Desktop Switch with 8-Port PoE+ and SFP Slot The TP-Link TL-SG1210P is a fanless 10-port Gigabit switch with PoE+ on eight ports, a dedicated Gigabit SFP fibre slot, and a 63W total PoE budget — all in a compact desktop form factor. Designed for small to medium IP camera installations, wireless AP deployments, and mixed wired/wireless office networks, it delivers data and power over a single cable to up to eight devices with no configuration required. The SFP slot adds flexibility for fibre uplinks to a core switch or NVR over longer distances. Key Features 8 × PoE+ Ports (Ports 1–8): IEEE 802.3af/at compliant, delivering up to 30W per port for IP cameras, wireless APs, VoIP phones, and access control devices. 63W Total PoE Budget: Sufficient to simultaneously power multiple cameras and APs from a single switch. 1 × Gigabit SFP Slot: Supports single-mode and multi-mode fibre transceivers for long-distance uplinks to a core switch, NVR, or fibre backbone — without running copper cable. 9 × Gigabit RJ45 Ports + 1 SFP: 10 total ports with full 10/100/1000Mbps Auto-Negotiation and Auto MDI/MDIX on all copper ports. Fanless Silent Operation: No moving parts — completely silent, suitable for offices, reception areas, and noise-sensitive environments. Plug and Play: No configuration, software, or web interface required — connect and power on. 802.1p/DSCP QoS: Prioritises latency-sensitive traffic such as VoIP and IP camera streams for consistent performance. IGMP Snooping: Optimises multicast traffic from IP cameras, reducing unnecessary bandwidth consumption across the network. Physical Security Lock: Kensington-style lock slot for securing the switch in accessible locations. 20Gbps Switching Capacity: Non-blocking architecture ensures full-speed performance across all ports simultaneously. Ideal Use Cases Powering and connecting up to 8 IP cameras in a CCTV installation without separate PoE injectors or power supplies. Deploying multiple wireless access points across an office, retail space, or warehouse from a single switch. Mixed installations combining IP cameras, APs, VoIP phones, and wired computers on a single compact switch. Using the SFP slot for a fibre uplink to a core switch or NVR located beyond the 100-metre copper cable limit. Small business networks requiring a silent, desktop-sized PoE switch with fibre uplink capability. Replacing multiple PoE injectors with a single managed-free switch for cleaner, more cost-effective installations. Technical Specifications Specification Detail Model TL-SG1210P RJ45 Ports 9 × 10/100/1000Mbps (8 PoE+, 1 standard) SFP Slot 1 × Gigabit SFP (MMF & SMF) PoE Ports Ports 1–8 (IEEE 802.3af/at) PoE Power per Port Up to 30W Total PoE Budget 63W Switching Capacity 20Gbps MAC Address Table 4K QoS 802.1p / DSCP IGMP Snooping Yes Transfer Method Store-and-Forward Fan Fanless (silent) Physical Security Security lock slot Power Supply External adapter (53.5VDC / 1.31A) Power Consumption (no PD) 7.11W @ 220V/50Hz Power Consumption (max PoE) 78.13W @ 220V/50Hz Operating Temperature 0°C – 40°C Dimensions 209 × 126 × 26 mm Weight 1.26kg Certifications CE, FCC, RoHS SKU TL-SG1210P Barcode (EAN) 1210002617062 What’s in the Box 1 × TL-SG1210P 10-Port Gigabit PoE+ Switch 1 × Power Adapter Installation Guide Frequently Asked Questions Which ports support PoE on the TL-SG1210P? Ports 1 through 8 are PoE+ capable (IEEE 802.3af/at). Port 9 is a standard Gigabit RJ45 uplink port, and Port 10 is the Gigabit SFP slot — neither supports PoE. What is the total PoE power budget? The TL-SG1210P has a 63W total PoE budget shared across all eight PoE ports. Each port can deliver up to 30W individually, but the combined draw across all eight ports cannot exceed 63W. How many IP cameras can I power simultaneously? Up to eight cameras. The actual number depends on each camera’s PoE power draw. For example, eight cameras drawing 7W each totals 56W — within the 63W budget. Higher-wattage cameras (e.g. PTZ cameras at 25–30W) will reduce the number that can be powered concurrently. What SFP transceivers are compatible with the SFP slot? The SFP slot supports standard Gigabit SFP transceivers for both multi-mode fibre (MMF, e.g. 1000BASE-SX) and single-mode fibre (SMF, e.g. 1000BASE-LX). TP-Link-branded SFP modules are recommended for guaranteed compatibility. SFP transceivers are sold separately. Does it require any configuration? No. The TL-SG1210P is fully plug and play. Connect your devices and power on — no web interface, software, or CLI configuration is required. What is the difference between the TL-SG1210P and the TL-SG1005LP? The TL-SG1210P has 10 ports (8 PoE+) with a 63W budget and a Gigabit SFP slot for fibre uplinks. The TL-SG1005LP has 5 ports (4 PoE+) with a 40W budget and no SFP slot. Choose the TL-SG1210P for larger installations requiring more PoE ports, higher budget, or fibre connectivity. What is the difference between the TL-SG1210P and the TL-SG116P? The TL-SG116P has 16 PoE+ ports with a 120W budget and is designed for larger deployments. The TL-SG1210P has 8 PoE+ ports with a 63W budget plus a Gigabit SFP slot, making it better suited for medium-sized installations that also need a fibre uplink option.

Read more less

Dahua CS4010-8ET-110 10-Port Cloud Managed Desktop Switch with 8-Port PoE Highly intuitive, the Smart Managed Switch can manage local networks. With the DoLynk Care platform, it can also perform cloud management. The switch performs operation and maintenance using topology visualization on front-end, transmission and back-end storage devices that are in the security system and IT system. With its fullmetal design, the switch has great heat dissipation and can operate in temperatures ranging -10°C to 55°C. It offers EMC and has protection against overvoltage, overcurrent, static electricity, lightning strikes, pulses and other types of interference. For the PoE series Smart Managed Switch, power is supplied up to 250 meters away. The orange port supplies up to 60 W and the red port provides up to 90 W. Also, link aggregation and STP are available on select models to ensure the network remains stable. The switch can be used in small and medium-sized businesses such as supermarkets, offices, restaurants, cafés and hotels. Features Meets the requirements of IEEE802.3,IEEE802.3u,IEEE802.3x,IEEE802.3ab standards Meets the requirements of IEEE802.3af, IEEE802.3at, Hi-PoE, and IEEE802.3bt power supply standards. Manages PoE power consumption and PoE power on/off. Supports Intelligent PoE. A wide operating temperature range and a full metal casing that is fully-enclosed and dust-proof. Specifications Dahua PoE Switch Ethernet Port 10 Optical Port Not support UpLink Port 2 PoE Budget Idling: 3 W, Full load: 110 W Layer Layer 2 Type Cloud Managed Downloads DH-CS4010-8ET-110 Datasheet DH-CS4010-8ET-110 Installation Method DH-CS4010-8ET-110 Quick Start Guide DH-CS4010-8ET-110 Dimension DH-CS4010-8ET-110 Drawings

Read more less

HiLook Transmission NS-0105P-35, 4 Port PoE Switch Unmanaged switch with 4 x 100 Mbps PoE ports and 1 x 100 Mbps uplink port All ports support 6 kV lighting protection 35 W PoE power budget Maximum transmission distance is 250 meters MAC address auto learning and auto aging Downloads Datasheet Communication Matrix

Read more less

HiLook NS-0106P-35 4 Port Fast Ethernet Unmanaged POE Switch 4 x 10/100Mbps PoE ports, and and 2 × 10/100Mbps RJ45 ports IEEE 802.3at/af standard for PoE ports (Max. 35 W PoE output). IEEE 802.3, IEEE 802.3u, and IEEE 802.3x standard. 6 KV surge protection for PoE ports. Up to 250 m long-range transmission. Wire-speed forwarding. Store-and-forward switching. Solid high-strength metal shell. Reliable fan-free design PoE Power Supply PoE Standard: Ports 1 to 4: IEEE 802.3af, IEEE 802.3at PoE Power Pin: Ports 1 to 4: Ethernet cables 1/2/3/6 and 4/5/7/8 provide power supply simultaneously. PoE Port: Ports 1 to 4 Max. Port Power: Ports 1 to 4: 30 W PoE Power Budget: 35 W Network Parameters Port Number: 4 x 10/100Mbps PoE ports, and and 2 × 10/100Mbps RJ45 ports Port Type: RJ45 port, full duplex, MDI/MDI-X adaptive Standard: IEEE 802.3, IEEE 802.3u, IEEE 802.3x Forwarding Mode: Store-and-forward switching High Priority Ports: Ports 1 and 2 Ports For Long-Distance Transmission: Ports 1 to 4 MAC Address Table: 4 K Switching Capacity: 1.6 Gbps Packet Forwarding Rate: 0.8928 Mpps Internal Cache: 768 Kbits Dialing Function Long Range: Ports 1 to 4: up to 250m. General Shell: Metal material, fan-free design Gross Weight: 0.52 Net Weight: 0.265 Dimension (L × H × D): 145 mm × 68.45 mm × 25.6 mm (5.71” × 2.69” × 1.01”) Operating Temperature: -10°C to 40°C (14°F to 104°F) Storage Temperature: -40°C to 85°C (-40°F to 185°F) Operating Humidity: 5% to 95% (no condensation) Storage Humidity: 5% to 95% (no condensation) Power Supply: 48 VDC, 0.8 A Power Consumption In Idle: < 5 W Power Souce: 38 W Max. Power Consumption: 38 W Downloads Command and Interface FileData SheetQuick Start GuideCommunication Matrix

Read more less

The USW-24-POE is a configurable Gigabit Layer 2 switch with twenty-four Gigabit Ethernet ports including sixteen auto-sensing 802.3at PoE+ ports, and two SFP ports. It provides Gigabit PoE links to your RJ45 Ethernet devices and Gigabit fiber uplink options to your enterprise network. The USW-24-POE features a 1.3" touch LCM to provide status information. With a depth of 7.9", the compact fanless design can be easily installed in a SOHO rack cabinet.Managed and configured by the UniFi Network Controller with UniFi mobile app support, the USW-24-POE offers an extensive suite of advanced Layer 2 switching protocols and features, including operation mode (switching, mirroring, or aggregate) per port. The UniFi Network Controller and mobile app allow admins to configure and monitor virtually all of the switch features in a graphical user interface from anywhere.

Read more less

The Ubiquiti UniFi Switch Pro 24 PoE is a powerful managed PoE+ switch offering 24 Gigabit Ethernet PoE+ portswith robust power budget, dual 10G SFP+ uplinks, and deep UniFi Network integration — ideal for enterprise and commercial LAN deployments. Professional Managed PoE+ Switching The UniFi Switch Pro 24 PoE delivers high performance, flexible PoE power distribution, and advanced network management for enterprise networks, surveillance systems, VoIP telephony, access control, and more. With 24× Gigabit PoE+ ports, this switch supports PoE standards including 802.3af/at/bt, enabling power delivery to cameras, access points, phones, and IoT devices without extra power injectors. High-Capacity PoE Power Budget Engineered for demanding networks, the UniFi Switch Pro 24 PoE offers a high total PoE power budget to support both legacy 802.3af devices and high-power PoE+ equipment simultaneously. Dual 10G SFP+ uplinks ensure robust connectivity to core networks or downstream aggregation. Advanced UniFi Network Management Seamlessly managed through the UniFi Network Controller, this switch provides features such as: VLAN segmentation PoE scheduling Port statistics & health 10G uplink redundancy LACP link aggregation This flexibility makes it ideal for smart buildings, enterprise campuses, and multi-service edge LAN deployments. Key Features & Benefits 24 × Gigabit PoE+ ports (802.3af/at/bt compatible) Dual 10G SFP+ uplinks for high-speed aggregation High total PoE power budget 400W Total PoE Power Supply Managed with UniFi Network app & controller Advanced VLAN, QoS, LACP support Rack-mountable metal chassis Ideal for CCTV, Wi-Fi, VoIP & IoT deployments NDAA-compliant options available What’s in the Box UniFi Switch Pro 24 PoE Rackmount brackets + screws Power cord Quick start guide Technical Specifications Specification Details Model UniFi Switch Pro 24 PoE Ports 24× Gigabit Ethernet PoE+ Uplink Ports 2× 10G SFP+ PoE Standards 802.3af / 802.3at / 802.3bt compatible Total PoE Supply 400W Managed UniFi Network Controller Layer L2 / Basic L3 (VLAN, static routing) VLAN Support Yes QoS Yes LACP Yes Form Factor Rack-mountable metal chassis Power AC internal PSU Controller Support UniFi Network Controller & mobile app FAQs Q: What PoE standards does this switch support?A: The UniFi Switch Pro 24 PoE supports 802.3af/at/bt and provides a high PoE power budget for diverse network devices. Q: Can I manage this switch remotely?A: Yes — with the UniFi Network Controller or mobile app. Q: What are the uplink options?A: Dual 10G SFP+ uplinks allow high-speed aggregation to core networks. Q: Is this suitable for CCTV & Wi-Fi deployments?A: Yes — ideal for powering UniFi cameras, APs, VoIP phones, and IoT devices. Downloads USW-Pro-24-POE DatasheetUSW-Pro-24-POE Installation Guide

Read more less

TP-Link TL-SL1311P 8-Port PoE+ Desktop Switch with Gigabit & SFP Uplinks The TP-Link TL-SL1311P is a compact, fanless 11-port desktop PoE+ switch designed for small business, retail, and surveillance installations across Australia. With eight 802.3af/at PoE+ ports, two Gigabit RJ45 uplinks, and one Gigabit SFP slot, it delivers both data and power over a single cable to IP cameras, access points, and VoIP phones — without the need for separate power adapters. Extend Mode pushes PoE power and data up to 250 metres for long-run camera installations, while Isolation Mode and PoE Auto Recovery add security and reliability in a completely silent, plug-and-play package. Key Features 8 × PoE+ Ports (802.3af/at) — Powers up to eight PoE devices simultaneously — up to 30W per port and 65W total budget — via a single Ethernet cable with no separate power adapters required. 2 × Gigabit RJ45 Uplink Ports — High-speed Gigabit uplinks connect the switch to your router, NVR, or core network switch for fast data throughput. 1 × Gigabit SFP Uplink Slot — Fibre or DAC uplink option for longer-distance or interference-free connections to a core switch or NVR. Extend Mode — Up to 250m PoE Range — Extends PoE power and data transmission up to 250 metres at 10Mbps on a single Cat5e/Cat6 cable — ideal for remote outdoor cameras beyond the standard 100m PoE limit. Isolation Mode — One-click client traffic separation prevents connected PoE devices from communicating with each other — improving security and performance in shared environments. PoE Auto Recovery — Automatically monitors and power-cycles unresponsive PoE devices — keeping IP cameras and access points online without manual intervention. Fanless & Silent — No moving parts means completely silent operation — ideal for office desks, reception areas, and comms rooms. Plug & Play — No configuration required; simply connect and power on for immediate operation. Compact Desktop Form Factor — Small footprint suitable for desk, shelf, or wall installation in space-constrained environments. Use Cases Small CCTV systems — power and connect up to 8 PoE IP cameras without separate injectors or power adapters Long-run camera installations — use Extend Mode to reach cameras up to 250m from the switch on a single cable run Small office and retail Wi-Fi — power PoE access points from a compact desktop switch without rack infrastructure VoIP phone deployments — power and connect IP desk phones with single-cable simplicity Isolated guest or IoT networks — use Isolation Mode to prevent PoE devices from accessing each other on shared networks Home offices and small server rooms needing a compact, silent PoE switch with a Gigabit SFP uplink option Technical Specifications Specification Detail Model TL-SL1311P PoE Ports 8 × 10/100Mbps RJ45 PoE+ (802.3af/at) Uplink Ports 2 × Gigabit RJ45 + 1 × Gigabit SFP Total Ports 11 (8 × PoE+ + 2 × Gigabit RJ45 + 1 × Gigabit SFP) PoE Standard IEEE 802.3af / 802.3at Max PoE Per Port 30W Total PoE Budget 65W Extend Mode Range Up to 250m at 10Mbps (Cat5e/Cat6) Isolation Mode Yes — one-click client traffic separation PoE Auto Recovery Yes Management Unmanaged (plug and play) Cooling Fanless (silent) Form Factor Desktop Weight 1.28 kg Warranty 2 Years Recommended Accessories TP-Link VIGI C330 3MP Full-Colour Outdoor Bullet Camera — Connect up to 8 VIGI PoE cameras directly to the TL-SL1311P for a complete small-site IP surveillance system. TP-Link VIGI NVR1104H-4P — Connect the NVR to one of the Gigabit uplink ports for centralised recording while cameras are powered by the TL-SL1311P’s PoE+ ports. TP-Link TL-SM331T RJ45 SFP Module — Use in the Gigabit SFP slot to connect via standard Cat6 copper cabling to a core switch or router. Cat6 Ethernet Cable — For reliable PoE+ data and power delivery to all connected devices; required for Extend Mode runs up to 250m. Frequently Asked Questions What is Extend Mode and how does it work? Extend Mode reduces the port speed to 10Mbps and extends the PoE power and data transmission range from the standard 100 metres up to 250 metres on a single Cat5e or Cat6 cable run. This is particularly useful for outdoor IP camera installations where the camera mounting point is further than 100 metres from the switch — eliminating the need for a PoE extender or additional switch at the midpoint. What is Isolation Mode? Isolation Mode prevents connected PoE devices from communicating directly with each other on the switch — all traffic is routed through the uplink port only. This improves security in environments where PoE devices should not have access to each other, such as guest Wi-Fi APs, IoT cameras, or shared office environments where device-to-device traffic is undesirable. Is the 65W PoE budget shared across all 8 ports? Yes. The 65W total PoE budget is shared across all 8 PoE+ ports. Each port supports up to 30W individually, but the combined draw of all connected PoE devices must not exceed 65W. For example, four 15W PoE cameras would draw 60W — within budget. Plan your PoE device power requirements before deployment to avoid exceeding the total budget. Does the TL-SL1311P require any configuration? No. The TL-SL1311P is an unmanaged switch that operates plug-and-play with no configuration required. Extend Mode and Isolation Mode are toggled via physical buttons or DIP switches on the unit — no software or web interface is needed. What is the difference between the 8 PoE ports and the 3 uplink ports? The 8 PoE+ ports run at 10/100Mbps and supply PoE power to connected devices such as cameras, APs, and phones. The 2 Gigabit RJ45 uplink ports and 1 Gigabit SFP uplink slot do not supply PoE power and are intended for connecting the switch to your router, NVR, or core network switch at Gigabit speed. Can I use the SFP slot for a fibre connection? Yes. The Gigabit SFP slot accepts standard SFP modules including single-mode and multi-mode fibre transceivers, as well as DAC (Direct Attach Copper) cables and RJ45 SFP modules such as the TP-Link TL-SM331T. This allows the TL-SL1311P to connect to a core switch or NVR via fibre for longer-distance or interference-free uplinks.

Read more less

TP-Link TL-SG105PE 5-Port Gigabit PoE+ Easy Smart Switch Reliable PoE+ Switching for IP Cameras, VoIP & Smart Devices The TP-Link TL-SG105PE is a compact, fanless 5-port Gigabit smart switch with 4 PoE+ ports and a 65 W total power budget. It delivers both data and power over a single Ethernet cable — making it an ideal choice for IP security cameras, wireless access points, and VoIP phones in homes, small offices, and commercial installations across Australia. Extend Mode pushes PoE reach up to 250 m for remote camera positions, and PoE Auto Recovery automatically restarts unresponsive powered devices without manual intervention. Key Features 4 × 802.3af/at PoE+ ports — up to 30 W per port, 65 W total PoE budget 5 × 10/100/1000 Mbps Gigabit RJ45 ports with Auto-Negotiation and Auto MDI/MDIX Fanless, silent operation — suitable for noise-sensitive environments PoE Auto Recovery — automatically restarts unresponsive PoE devices Extend Mode — supports PoE transmission up to 250 m at 10 Mbps VLAN support — up to 32 active VLANs (MTU, Port, and Tag-based) QoS with Port-Based, 802.1p, and DSCP priority — 4 priority queues IGMP Snooping V1/V2/V3, Port Mirroring, Loop Prevention, Cable Diagnostics Web-based GUI and Easy Smart Configuration Utility for simple setup 10 Gbps switching capacity, 7.44 Mpps forwarding rate Use Cases IP CCTV Systems: Power and connect up to 4 PoE IP cameras without separate power supplies — ideal for small surveillance installations. Wireless Access Points: Deploy PoE-powered APs throughout a small office or retail space without additional power cabling. VoIP Phones: Prioritise voice traffic with QoS to ensure call quality on small business phone systems. Long-Run Installations: Use Extend Mode to push PoE up to 250 m for remote camera positions where cable runs are long. Small Office Networks: Segment traffic with VLANs and monitor network health with port mirroring and cable diagnostics. Specifications Specification Detail Model TL-SG105PE Total Ports 5 × 10/100/1000 Mbps RJ45 PoE Ports Ports 1–4 (802.3af/at PoE+) PoE Power Per Port Up to 30 W Total PoE Budget 65 W Switching Capacity 10 Gbps Forwarding Rate 7.44 Mpps MAC Address Table 2K Packet Buffer 1.5 Mb Jumbo Frame 16 KB VLAN Up to 32 active VLANs (4K VLAN IDs) QoS Port-Based / 802.1p / DSCP, 4 queues Extend Mode Up to 250 m at 10 Mbps Power Supply External adapter — 53.5 V DC / 1.31 A Max Power Consumption 4.52 W (no PD) / 75.16 W (full PoE load) Cooling Fanless Standards IEEE 802.3i/u/ab/af/at/x, 802.1q, 802.1p Weight 0.76 kg Frequently Asked Questions How many PoE cameras can I connect to the TL-SG105PE? You can connect up to 4 PoE-powered devices (ports 1–4). The total PoE budget is 65 W — if each camera draws 15 W, all 4 ports can run simultaneously at full load. Higher-draw devices (e.g., PTZ cameras at 25–30 W) will reduce the number of simultaneous powered ports. Does this switch require any configuration out of the box? No. It works plug-and-play for basic switching and PoE. The web GUI and Easy Smart Configuration Utility are available for advanced features like VLANs, QoS, and port mirroring when needed. Is the TL-SG105PE compatible with non-TP-Link PoE cameras? Yes. It complies with the IEEE 802.3af/at standard, so it is compatible with any standards-compliant PoE or PoE+ device regardless of brand. What is Extend Mode and when should I use it? Extend Mode reduces port speed to 10 Mbps to extend PoE transmission range up to 250 m. It is useful for remote camera positions where the cable run exceeds the standard 100 m Ethernet limit. What is PoE Auto Recovery? PoE Auto Recovery periodically checks the status of connected PoE devices. If a device becomes unresponsive (e.g., a frozen IP camera), the switch automatically power-cycles that port to restart the device — without any manual intervention. Does the switch have a fan? No. The TL-SG105PE is completely fanless, making it silent and suitable for offices, reception areas, server cabinets, or any noise-sensitive environment.

Read more less

The Dahua DH-CS4228-24GT-375 is a robust Layer 2 Smart Managed Gigabit Switch designed for small-to-medium businesses and professional CCTV deployments. Featuring 24 PoE+ ports, cloud-based DoLynk management, STP loop protection, PoE watchdog, and 250m long-distance PoE support — it’s a reliable backbone for modern IP surveillance and networking. Key Features 28 ports total: 24 × RJ45 PoE + 2 × RJ45 uplink + 2 × SFP uplink Cloud-managed via DoLynk Care App (real-time monitoring, alerts, topology) PoE output up to 90W on red ports, 30W on standard ports, 375W total PoE budget Long-distance PoE up to 250m (bandwidth throttled) Intelligent PoE management with watchdog auto recovery IEEE802.3af/at/bt & Hi-PoE compliant Spanning Tree Protocol (STP/RSTP) for redundancy and loop protection 56 Gbps switching capacity, 41.66 Mpps forwarding rate Rack or desktop mountable full metal casing with wide -10°C to 55°C temp support Ideal for use in hotels, cafes, retail shops, and medium-sized offices Technical Specifications Technical Specifications – Dahua DH-CS4228-24GT-375 Total Ports 28 (24 × PoE RJ45, 2 × Uplink RJ45, 2 × SFP Uplink) PoE Output Port 1-2: ≤90W, Port 3–24: ≤30W, Total: ≤375W PoE Standards IEEE802.3af/at/bt, Hi-PoE Management Web UI & DoLynk App (cloud-based) Layer Layer 2 Smart Managed Switching Capacity 56 Gbps Forwarding Rate 41.66 Mpps Packet Buffer 4 Mbit Jumbo Frame 15K Bytes MAC Address Table 8K entries Operating Temp -10°C to +55°C Installation Rack mount / Desktop mount PoE Watchdog Yes – automatic recovery on port failure Loop Protection STP/RSTP + Loop Alarm Dimensions 440 × 220 × 44 mm Weight 2.66 kg (Net), 3.26 kg (Gross) Power Supply Built-in 100–240V AC, 50/60 Hz Lightning/Static Protection 4 kV/2 kV lightning; 8 kV/6 kV static Certifications CE, FCC, RoHS More Information DH-CS4228-24GT-375 Datasheet

Read more less

IP-COM G1110PF-8-102W 9GE+1SFP Ethernet Unmanaged Switch With 8-Port PoE Features: Compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3x, IEEE 802.3af/at standards 8*10/100/1000 Mbps Base-T Ethernet ports (Data/Power) 1*10/100/1000 Mbps Base-T Ethernet port (Data), 1*100/1000 Mbps Base-X SFP port 16 K MAC address table and MAC address auto-learning IEEE 802.3x full duplex flow control and backpressure half duplex flow control 20 Gbps switching fabric for non-blocking line-speed forwarding Maximum PoE output of a single port: 30 W Total power consumption of the switch: 102 W Three-mode toggle: Standard, VLAN Downloads G1110PF-8-102W Datasheet G1110PF-8-102W Quick Installation Guide

Read more less

Compact Gigabit PoE++ Power for Desktops, Workbenches & Small Installations The TP-Link TL-SG1006PP is a plug-and-play 6-port gigabit desktop switch that delivers both data and power over a single Ethernet cable. With one 60W PoE++ port and three 30W PoE+ ports, it's purpose-built for powering high-demand devices like PTZ cameras, wireless access points, and VoIP phones — all from a compact, fanless desktop unit. Ideal for small offices, retail counters, and on-site security installations across Australia. Key Features 1× PoE++ Port (802.3bt) — Up to 60W — Power high-demand devices such as PTZ cameras, multi-radio access points, or thin clients from a single port. 3× PoE+ Ports (802.3at/af) — Up to 30W Each — Power standard IP cameras, VoIP phones, and wireless APs without separate power adaptors. 64W Total PoE Budget — Sufficient for a mixed deployment of PoE and PoE++ devices in a small installation. 6× Gigabit RJ45 Ports — Full gigabit speeds across all ports for fast, low-latency data transfer. Extend Mode (up to 250m) — Extend PoE data and power transmission up to 250 metres at 10 Mbps — useful for cameras positioned far from the switch. PoE Auto Recovery — Automatically detects and reboots unresponsive PoE devices, reducing the need for manual intervention on-site. 802.1p/DSCP QoS — Prioritises latency-sensitive traffic such as video streams and VoIP calls for smoother performance. Plug and Play — No configuration, no software, no login. Connect and go. Desktop Form Factor — Compact and fanless design suits desktops, shelves, and small comms enclosures. Use Cases PTZ Camera Power — The 60W PoE++ port can power demanding PTZ cameras that exceed standard PoE+ limits. Small CCTV Installations — Power up to 3 standard IP cameras and one high-power device from a single compact switch. Small Office Networking — Connect workstations, a VoIP phone, and a wireless AP from one desktop unit without a rack. Retail & Hospitality — Discreet desktop placement behind a counter to power a camera, EFTPOS terminal hub, and AP simultaneously. Remote or Extended Runs — Use Extend Mode to reach cameras or APs up to 250m away without additional hardware. IT Technicians On-Site — Portable plug-and-play switch for temporary deployments, testing, or staged rollouts. Technical Specifications Specification Detail Model TL-SG1006PP Total Ports 6× 10/100/1000 Mbps RJ45 PoE++ Port 1× Port (802.3bt) — up to 60W PoE+ Ports 3× Ports (802.3at/af) — up to 30W each Total PoE Budget 64W PoE Standards IEEE 802.3af / 802.3at / 802.3bt QoS 802.1p / DSCP Extend Mode Range Up to 250m at 10 Mbps PoE Auto Recovery Yes Form Factor Desktop (fanless) Weight 860g Vendor TP-Link Downloads 📄 Download TL-SG1006PP Datasheet (PDF) Frequently Asked Questions What is the difference between PoE, PoE+, and PoE++? PoE (802.3af) delivers up to 15.4W per port, PoE+ (802.3at) delivers up to 30W, and PoE++ (802.3bt) delivers up to 60W or 90W depending on the type. The TL-SG1006PP includes one 60W PoE++ port and three 30W PoE+ ports, making it suitable for both standard and high-power devices. Can I power a PTZ camera from this switch? Yes. PTZ cameras typically require 25–50W depending on the model. The 60W PoE++ port on the TL-SG1006PP can comfortably power most PTZ cameras. Check your camera's power specification before connecting. Does the 64W PoE budget cover all 4 PoE ports simultaneously? The total PoE budget is 64W shared across all PoE ports. If you connect a 60W device to the PoE++ port, the remaining 4W is available for the PoE+ ports. Plan your device power draw accordingly to avoid exceeding the budget. Does this switch require any configuration? No. The TL-SG1006PP is fully unmanaged and plug-and-play. Extend Mode and other hardware features are toggled via physical DIP switches on the unit — no software or login required. What is PoE Auto Recovery and why does it matter? PoE Auto Recovery monitors connected PoE devices and automatically power-cycles any that become unresponsive. This is particularly useful for IP cameras and wireless APs that may occasionally freeze, eliminating the need for a manual site visit to reboot the device. Is this switch suitable for outdoor use? No. The TL-SG1006PP is designed for indoor desktop use. For outdoor or harsh-environment installations, use a weatherproof enclosure or choose a switch rated for outdoor deployment.

Read more less

HiLook NS-0310P-60 8 Port Fast Ethernet Unmanaged POE Switch 8 × 10/100Mbps PoE ports, and and 2 × Gigabit RJ45 port. IEEE 802.3at/af standard for PoE ports (Max. 60 W PoE output). IEEE 802.3, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z and IEEE 802.3ab standard. 6 KV surge protection for PoE ports. Up to 250 m long-range transmission. Wire-speed forwarding. Store-and-forward switching Solid high-strength metal shell. Reliable fan-free design. PoE Power Supply PoE Standard: Ports 1 to 8: IEEE 802.3af, IEEE 802.3at PoE Power Pin: Ports 1 to 4: Ethernet cables 1/2/3/6 and 4/5/7/8 provide power supply simultaneously. PoE Port: Ports 1 to 8 Max. Port Power: Ports 1 to 8: 30 W PoE Power Budget: 60 W Network Parameters Port Number: 8 × 10/100Mbps PoE ports, and and 2 × Gigabit RJ45 ports Port Type: RJ45 port, full duplex, MDI/MDI-X adaptive Standard: IEEE 802.3, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z and IEEE 802.3ab Forwarding Mode: Store-and-forward switching Working Mode: Standard mode (default), Extend mode Ports For Long-Distance Transmission: Ports 1 to 8 MAC Address Table: 16 K Switching Capacity: 5.6 Gbps Packet Forwarding Rate: 4.1664 Mpps Internal Cache: 4 Mbits Dialing Function Long Range: Ports 1 to 8: up to 250 m. General Shell: Metal material, fan-free design Gross Weight: 1.20 Net Weight: 0.555 Dimension (L × H × D): 217.6 mm × 103.35 mm × 27.8 mm (8.57” × 4.07” × 1.09”) Operating Temperature: -10°C to 40°C (14°F to 104°F) Storage Temperature: -40°C to 85 °C -40°F to 185°F) Operating Humidity: 5% to 95% (no condensation) Storage Humidity: 5% to 95% (no condensation) Power Supply: 48 VDC, 1.35 A Power Consumption In Idle: < 5 W Power Souce: 65 W Max. Power Consumption: 65 W Downloads Command and Interface FileData SheetQuick Start GuideCommunication Matrix

Read more less

Layer 2 switch with (5) GbE RJ45 ports, including (1) 802.3af PoE input.The Switch Flex Mini (USW Flex Mini) is a fully managed, Layer 2 switch with (5) GbE RJ45 ports, including (1) 802.3af PoE input. The USW Flex Mini can be powered with either PoE (via Port 1) or its included USB-C power adapter*. This switch can also be monitored or configured from anywhere with the powerful, intuitive UniFi Network web application and mobile app. Features: (1) GbE, 802.3af PoE RJ45 input(4) GbE RJ45 portsCompact, slim housingCan be powered with a 5V, 1A USB-C adapter (Only Comes In Single Pack)

Read more less

Flexible five-port, Layer 2 PoE switch that can be powered with PoE++.Features: (1) GbE, PoE++ RJ45 input (4) GbE, PoE+ RJ45 ports Up to a 46W total PoE supply* Weatherproof design with multiple mounting options Managed with the UniFi Network application: Version 5.10.3 and later *When powered with a PoE++ switch or a 60W PoE adapter (sold separately). DownloadsDatasheet Installation Guide

Read more less

Ubiquiti UniFi 16-port Managed Gigabit Switch - 8x PoE+ Ports, 8x Gigabit Ethernet Ports, 2x SFP , 42W, Touch Display, Fanless , GEN2 A 16-port, Layer 2 PoE switch with a silent, fanless cooling system. Features (8) GbE PoE+, (8) GbE ports (2) 1G SFP ports 42W total PoE availability Fanless, silent cooling Technical Specifications Mechanical Dimensions 442 x 200 x 44 mm (17.4 x 7.9 x 1.7") Weight Without mounting brackets: 2.8 kg (6.2 lb)With mounting brackets: 2.9 kg (6.4 lb) Enclosure material SGCC steel Hardware Management interface Ethernet In-Band Networking interface (16) GbE RJ45 ports(2) 1G SFP ports PoE interface (8) PoE/PoE+ (Pins 1, 2+; 3, 6-) Total non-blocking throughput 18 Gbps Switching capacity 36 Gbps Forwarding rate 26.78 Mpps Power method Universal input, 100—240V AC, 50/60 Hz Power supply AC/DC, internal, 60W Supported voltage range 100—240V AC Max. power consumption 18W (Excluding PoE output) Total available PoE 42W Max. PoE wattage per port by PSE PoE+: 32W Voltage range PoE mode PoE: 44—57VPoE+: 50—57V ESD/EMP protection Air: ± 16kV, contact: ± 12kV LCM display (1) 1.3" touchscreen Button Factory reset Shock and vibration ETSI300-019-1.4 Standard Ambient operating temperature -5 to 40° C (23 to 104° F) Ambient operating humidity 10 to 90% noncondensing Certifications CE, FCC, IC Switching Features Layer 2 features IGMP snoopingSTP / RSTP with priorities and port-level disablePort isolationStorm controlVoice VLANPort mirroringLACP port aggregationMulticast / broadcast rate limitingMAC address blockingFlow control802.1X controlJumbo framesProprietary loop protectionDHCP snooping / guardingEgress rate limitLLDP-MEDPort restricted by MACDevice isolation with ACLs Layer 3 features – LEDs System Status Ethernet PoESpeed/link/activity SFP Link/activity Application Requirements UniFi Network Version 7.2.94 and later Downloads USW-16-POE Installation Guide

Read more less

UniFi Pro Aggregation Switch The Switch Pro Aggregation is a fully managed, Layer 3 switch with (28) 10G SFP+ ports and (4) 25G SFP28 ports designed to enhance your network's switching capacity and performance by creating high-bandwidth aggregation links. This rack-mountable switch also offers 760 Gbps switching capacity and features a 1.3" LCM color touchscreen that concisely displays key system and connection insights.Additionally, the Switch Pro Aggregation offers enhanced power supply failure protection when connected to the SmartPower Redundant Power System (USP RPS sold separately). This switch can be monitored or configured from anywhere with the powerful, intuitive UniFi Network web application and mobile app. Features: (1) 1.3” LCM color touchscreen with AR switch management (28) 10G SFP+ ports (4) 25G SFP28 ports (1) USP RPS DC input 760 Gbps switching capacity Layer 3 switching features Mechanical Dimensions 442 x 325 x 44 mm (17.4 x 12.8 x 1.7") Weight Without Mount: 4.6 kg (10.14 lb) With Mount: 4.7 kg (10.36 lb) Enclosure Material SGCC Steel Hardware Total Non-Blocking Throughput 380 Gbps Switching Capacity 760 Gbps Forwarding Rate 565.44 Mpps Max. Power Consumption 100W Power Method (1) Universal AC input, 100-240VAC, 2A Max, 50/60 Hz (1) USP-RPS DC input, 11.5VDC, 8.7A Power Supply AC/DC, Internal, 100W Network Interface (28) 1/10 Gbps SFP+ Ethernet (4) 1/10/25 Gbps SFP28 Ethernet* LCM Display (1) 1.3" Touchscreen Management Interface Ethernet In-Band Modes SMB Layer 3 10/25 G Fiber Switch ESD/EMP Protection Air: ± 16kV, Contact: ± 12kV Operating Temperature -5 to 40° C (23 to 104° F) Operating Humidity 10 - 90% Noncondensing *The four SFP28 ports don't support mixed speed at 25Gbps mode. Once one of the SFP28 ports is configured at 25Gbps mode, the others will be limited at 25Gbps too. The SFP28 ports only support mixed speed when all ports are at 1Gbps or 10Gbps. Downloads Datasheet Installation Guide

Read more less

The USW Flex Utility is an outdoor weatherproof enclosure designed for use with the UniFi Switch Flex, USW-Flex. It includes an Ethernet patch cable and a 60W PoE adapter, which provides a maximum PoE budget of 46W. The USW Flex Utility can be easily mounted on a pole, provides clean cable management and screw lock for security. Downloads Datasheet

Read more less

Power and Connect Up to 24 IP Cameras or PoE Devices — No Configuration Required The TP-Link TL-SL1226P is a rack-mountable 24-port PoE+ unmanaged switch built for security installers and network professionals who need reliable, high-power PoE delivery without the complexity of managed switching. With a 250W PoE budget, 250m Extend Mode, and plug-and-play operation, it's one of the most practical switches for IP camera deployments across Australian commercial and residential installations. Key Features 24× PoE+ Ports (802.3at/af) — Power and connect IP cameras, VoIP phones, and wireless access points over a single Cat5e/6 cable, up to 30W per port. 250W Total PoE Budget — Sufficient headroom to simultaneously power a full deployment of standard IP cameras or mixed PoE devices. Extend Mode (up to 250m) — Transmit data and power up to 250 metres at 10 Mbps — ideal for large sites where cameras are positioned far from the switch. Priority Mode — Ports 1–8 are automatically assigned high priority, ensuring video streams from critical cameras are never starved of bandwidth. Isolation Mode — One-click client traffic separation improves network security and performance in multi-tenant or shared environments. 2× Gigabit RJ45 Uplinks + 2× Combo SFP Slots — Flexible uplink options for connecting to your core network switch or fibre backbone. Plug and Play — No software, no login, no configuration. Unbox, rack, and connect. Physical Security Lock — Prevents accidental disconnection of the power cable in rack environments. Use Cases IP CCTV Installations — Power and connect up to 24 IP cameras from a single switch in commercial or multi-site surveillance deployments. VoIP Phone Systems — Deliver power and data to desk phones across an office floor without separate power adaptors. Wireless Access Point Deployments — Power ceiling-mounted APs throughout a building from a central comms room. Large-Site Surveillance (Extend Mode) — Reach cameras in car parks, warehouses, or perimeter locations up to 250m away without a media converter. Education & Hospitality — Isolation Mode makes it suitable for guest networks or student lab environments requiring traffic separation. Technical Specifications Specification Detail Model TL-SL1226P PoE Ports 24× 10/100 Mbps RJ45 (PoE+, 802.3at/af) Uplink Ports 2× Gigabit RJ45 + 2× Combo Gigabit SFP PoE Power Budget 250W total / up to 30W per port Switching Capacity 8.8 Gbps MAC Address Table 8K Extend Mode Range Up to 250m at 10 Mbps Dimensions (W×D×H) 440 × 180 × 44 mm (1U Rack) Power Supply 100–240V AC, 50/60 Hz Max Power Consumption 18.32W (no PD) / 294W (250W PD load) Cooling 2× Internal Fans Physical Security Lock Yes Network Media Cat3/4/5 (10BASE-T), Cat5/5e (100BASE-TX), Cat5e/6+ (1000BASE-T), MMF/SMF (1000BASE-X) Certifications FCC, CE, RoHS Frequently Asked Questions How many IP cameras can this switch power simultaneously? With a 250W PoE budget and up to 30W per port, the TL-SL1226P can power up to 24 cameras. In practice, the number depends on each camera's power draw. Most standard IP cameras consume 5–15W, so you can typically run a full 24-camera deployment comfortably within the budget. What is Extend Mode and when should I use it? Extend Mode reduces the port speed to 10 Mbps and extends the PoE transmission range from the standard 100m up to 250m. Use it when cameras are located far from the switch — such as in car parks, warehouses, or along building perimeters — to avoid running additional cable or installing a media converter. Does this switch require any software or configuration? No. The TL-SL1226P is fully unmanaged and plug-and-play. Simply connect your devices and it operates automatically. Extend Mode, Priority Mode, and Isolation Mode are toggled via physical DIP switches on the unit — no login or software required. Can I connect this to a fibre uplink? Yes. The two combo Gigabit SFP slots accept standard SFP modules (sold separately), allowing you to connect to a fibre backbone or a core managed switch in your comms room. Is this switch rack-mountable? Yes. The TL-SL1226P is a 1U rack-mount unit (440mm wide) and includes rack-mount hardware in the box, making it suitable for standard 19-inch equipment racks. What's the difference between Priority Mode and Isolation Mode? Priority Mode assigns higher bandwidth priority to ports 1–8, ensuring video streams from critical cameras are not disrupted by other traffic. Isolation Mode prevents connected devices from communicating directly with each other through the switch, improving security and reducing broadcast traffic — useful in multi-tenant or guest network scenarios.

Read more less

16-Port Gigabit PoE+ Switch Built for CCTV and SMB Networks The TP-Link TL-SG1218MPE is a JetStream Easy Smart switch that combines 16 Gigabit PoE+ ports, a 192W power budget, and intelligent traffic management in a rack-mountable 1U chassis. Designed for small to medium business surveillance systems, wireless deployments, and IP phone networks, it delivers the performance and control of a managed switch with the simplicity of easy smart configuration — no advanced networking expertise required. Key Features 16× Gigabit PoE+ Ports (802.3at/af): Power and connect IP cameras, wireless access points, VoIP phones, and other PoE/PoE+ devices across all 16 ports simultaneously. 192W Total PoE Budget: One of the highest PoE budgets in its class — supports a full deployment of 16 standard PoE cameras or a mixed load of PoE+ devices. 2× SFP Fibre Uplink Ports: Connect to fibre backbone switches or extend your network over long distances using single-mode or multi-mode fibre. QoS (Quality of Service): Prioritises video and voice traffic to ensure smooth, uninterrupted camera feeds and VoIP calls even under heavy network load. IGMP Snooping: Optimises multicast traffic for IPTV and IP camera streams, reducing unnecessary bandwidth consumption across the network. Port Priority: Assign priority to specific ports to guarantee performance for latency-sensitive devices such as IP cameras and NVRs. Intelligent PoE Power Management: Automatically monitors and manages PoE power distribution to protect against overload. 802.1Q VLAN Support: Segment your network for improved security and traffic isolation between cameras, staff devices, and guest networks. Rack Mountable (1U): Standard 19-inch rack form factor (440 × 180 × 44mm) for clean, professional installations in comms cabinets and server rooms. 36 Gbps Switching Capacity: Non-blocking switching fabric handles high-bandwidth video streams from multiple cameras without bottlenecks. Common Use Cases 16-camera IP CCTV systems for retail, warehouses, and commercial buildings Multi-access-point Wi-Fi deployments in offices, schools, and hospitality venues VoIP phone networks for small to medium businesses Mixed PoE/PoE+ deployments requiring high total power budgets Network segmentation with VLAN for security-conscious installations Fibre uplink to a core switch in multi-floor or multi-building networks Technical Specifications Model TL-SG1218MPE RJ45 Ports 16× 10/100/1000Mbps (all PoE+) SFP Ports 2× Gigabit SFP (fibre uplink) PoE Standard IEEE 802.3at (PoE+) / 802.3af (PoE) Total PoE Budget 192W Switching Capacity 36 Gbps Packet Forwarding Rate 23.8 Mpps MAC Address Table 8K Packet Buffer Memory 4.1 Mbit Jumbo Frame 9KB VLAN 802.1Q VLAN QoS Yes (802.1p) IGMP Snooping Yes Fans 2× (active cooling) Physical Security Lock Yes Mounting Rack mountable (19″, 1U) Dimensions (W × D × H) 440 × 180 × 44mm Power Supply 100–240V AC, 50/60Hz (internal) Max Power Consumption 18.73W (no PD) / 217.22W (full PoE load) Standards IEEE 802.3/802.3u/802.3ab/802.3x/802.3af/802.3at/802.1q/802.1p Management Easy Smart (web UI) Frequently Asked Questions What is an “Easy Smart” switch? Easy Smart is TP-Link's simplified management tier — it provides a web-based interface for configuring features like VLANs, QoS, port priority, and IGMP Snooping without the complexity of a fully managed switch. It's ideal for installers and IT staff who need more control than an unmanaged switch but don't require enterprise-level CLI management. Does the TL-SG1218MPE support PoE+ (802.3at)? Yes. All 16 RJ45 ports support both IEEE 802.3af (PoE, up to 15.4W) and IEEE 802.3at (PoE+, up to 30W per port), subject to the 192W total power budget shared across all ports. How many cameras can I connect? Up to 16 IP cameras can be connected via the PoE+ ports. For standard 802.3af cameras drawing around 10–12W each, the 192W budget comfortably supports a full 16-camera deployment. For higher-power PTZ or PoE+ cameras, calculate your total load to stay within the 192W budget. What are the SFP ports used for? The two SFP ports accept Gigabit fibre modules (single-mode or multi-mode) for uplink connections to a core switch or to extend your network over long distances — useful in multi-building or multi-floor installations where copper Ethernet is impractical. Can I set up VLANs on this switch? Yes. The TL-SG1218MPE supports 802.1Q VLAN configuration via its web-based Easy Smart interface, allowing you to segment camera traffic, staff devices, and guest networks onto separate logical networks for improved security and performance. Is it rack mountable? Yes. The TL-SG1218MPE is a standard 1U rack-mountable switch (440mm wide) and includes rack mounting brackets. It fits any standard 19-inch equipment rack or comms cabinet.

Read more less

Reliable Multi-WAN Routing and Secure VPN for Australian BusinessesThe TP-Link TL-ER605 is a Gigabit Multi-WAN VPN router built for small to medium businesses that need always-on internet connectivity, secure remote access, and centralised network management. With up to four WAN ports for load balancing and automatic failover, plus full integration with the TP-Link Omada SDN platform, the ER605 delivers enterprise-grade performance at a practical price point.Key Features Five Gigabit Ports — 1 fixed WAN + 3 configurable WAN/LAN + 1 fixed LAN for flexible deployment Up to 4 Active WAN Ports — load balancing and automatic failover across multiple internet connections Highly Secure VPN — supports 20× IPsec, 16× OpenVPN, 16× L2TP, and 16× PPTP tunnels simultaneously 41.5 Mbps IPsec Throughput — fast, encrypted site-to-site and remote access VPN Omada SDN Integration — Zero-Touch Provisioning, centralised cloud management, and intelligent monitoring via Omada app or controller Advanced Security — SPI firewall, DoS defence, IP/MAC/URL filtering 25,000 Concurrent Sessions — handles demanding network loads with ease Flexible WAN Types — PPPoE, Static IP, Dynamic IP, L2TP, PPTP Typical Use Cases Multi-WAN failover for businesses requiring always-on internet (NBN + 4G/5G backup) Secure site-to-site VPN between office locations or remote workers Centralised management of multi-site networks via Omada Cloud Controller Gateway router for CCTV and IP security systems requiring remote VPN access Retail, hospitality, and SMB environments needing robust firewall and content filtering Technical Specifications Specification Detail Model TL-ER605 WAN Ports 1× fixed Gigabit WAN + 3× configurable Gigabit WAN/LAN LAN Ports 1× fixed Gigabit LAN (+ up to 3 configurable) Total Gigabit Ports 5 Standards IEEE 802.3, 802.3u, 802.3ab, 802.3x, 802.1q VPN Tunnels 20× IPsec, 16× OpenVPN, 16× L2TP, 16× PPTP IPsec VPN Throughput 41.5 Mbps Concurrent Sessions 25,000 WAN Connection Types PPPoE, Static IP, Dynamic IP, L2TP, PPTP Flash Memory 16MB SPI DRAM 128MB Power Supply External 9V / 0.85A DC Adapter Dimensions (W×D×H) 158 × 101 × 25 mm Management Omada App, Omada Cloud Controller, Omada Hardware Controller, Web UI Certifications FCC, CE, RoHS Warranty 5 Years Frequently Asked Questions Do I need an Omada controller to use the TL-ER605? No. The ER605 works as a standalone router straight out of the box. An Omada controller (software, cloud, or hardware) is optional and only required if you want centralised multi-device management across a site or multiple sites. Does the ER605 support NBN connections in Australia? Yes. It supports PPPoE, Dynamic IP, Static IP, L2TP, and PPTP WAN types, covering all common NBN connection methods including FTTP, FTTC, FTTN, and HFC. L2TP support also covers NBN services delivered via some Australian ISPs. How many remote VPN users can connect at once? The ER605 supports up to 16 simultaneous OpenVPN tunnels and 16 L2TP tunnels, making it well-suited for small teams needing secure remote access to office resources or CCTV systems. What is the difference between load balancing and failover? Load balancing distributes outbound traffic across multiple WAN connections simultaneously to maximise available bandwidth. Failover automatically switches all traffic to a secondary WAN if the primary connection drops. The ER605 supports both modes. Is the ER605 suitable as a gateway for a CCTV network? Yes. It is commonly deployed as the gateway router in IP camera installations, providing VPN-based remote access to NVRs and cameras without exposing them directly to the internet.

Read more less

Dahua DH-PFT1500 5-Port PoE Extender with Long-Distance Transmission The Dahua DH-PFT1500 is an industrial-grade PoE extender designed to significantly extend Ethernet and PoE transmission distance for CCTV and network deployments. Working alongside standard PoE switches and injectors, the DH-PFT1500 extends PoE transmission up to 250 metres, making it ideal for large sites where cameras are installed far from the network core. Featuring 1 × Gigabit PoE input and 4 × 100Mbps PoE output ports, including Hi-PoE and IEEE 802.3bt support on red ports, the DH-PFT1500 can power high-demand devices such as PTZ cameras, AI cameras and multi-sensor cameras. Its full-metal, fanless design and wide operating temperature range ensure stable operation in harsh outdoor and industrial environments. Key Features 1 × Gigabit PoE input and 4 × 100Mbps PoE output ports Supports IEEE 802.3af / at / bt and Hi-PoE standards Long-distance PoE transmission up to 250m (10Mbps mode) Red ports support up to 90W Hi-PoE output PoE Watchdog automatically restarts unresponsive devices Full-metal, fanless industrial design Lightning protection: 4kV common mode / 2kV differential mode Desktop and DIN-rail mounting supported Designed for parks, roads, malls, factories and construction sites Specification Details Model / SKU DH-PFT1500 Ports 4 × RJ45 10/100 Mbps PoE output, 1 × RJ45 10/100/1000 Mbps PoE input PoE Standards IEEE 802.3af / 802.3at / IEEE 802.3bt / Hi-PoE PoE Power Output Port 1 ≤ 90W, Ports 2–4 ≤ 30W, Total ≤ 90W Long-Distance PoE Up to 250m (bandwidth reduced to 10Mbps) Switching Capacity 2.8 Gbps Forwarding Rate 2.08 Mpps Packet Buffer 1 Mbit MAC Address Table 4K Jumbo Frame 9K Bytes Operating Temperature –30°C to +65°C Operating Humidity 5%–95% RH Power Consumption Idle: 5W | Full Load: 90W Protection ESD: 8kV air / 6kV contact; Lightning: 4kV common / 2kV differential Installation Desktop mount or DIN-rail mount Dimensions 150 × 100 × 30 mm Net Weight 0.47 kg Certifications CE, FCC More Information DH-PFT1500 Datasheet

Read more less

The Ubiquiti USW-Pro-Max-16-PoE is a high-performance 16-port Layer 3 switch with PoE++ support and 2.5 GbE ports, built for demanding UniFi networks. Whether rack-mounted or set up on a desktop, it delivers professional-grade switching for small to medium business and advanced home deployments in Australia. Key Features 16 high-speed ports with 2.5 GbE support   PoE++ capability for high-power devices such as cameras, APs, lighting   Layer 3 switching for robust enterprise-grade networking   Rack-mount or desktop deployment flexibility   Seamless integration into UniFi Network application   Ideal for advanced home labs, SMB networks and UniFi deployments   Technical Specifications Ports 16 × RJ-45 (up to 2.5 GbE) + 2 × SFP+ uplinks PoE Support PoE++ (up to 90 W per port / total budget 180 W) Switching Capacity — (as per Ubiquiti spec sheet) Layer Layer 3 functionality Mounting Options Rack-mount (1U) or desktop Management UniFi Network application Dimensions (verify exact model size) Certifications CE, FCC, IC – NDAA compliant More Information USW-Pro-Max-16-PoE Datasheet USW-Pro-Max-16-PoE Installation Guide

Read more less

The Wi-Tek Wiking WK-PS219GF is a robust 16-port 100Mbps PoE switch designed for professional CCTV and IP deployments. With 2 gigabit RJ45 uplinks and 1 SFP slot, it provides flexible network expansion. Delivering a 180W PoE budget, it powers multiple cameras, access points, and IP devices with stability and efficiency. Port 1 supports Hi-PoE 60W for high-demand devices like PTZ cameras, while Ports 2–16 comply with IEEE 802.3af/at standards. A smart DIP switch enables 250m Extend mode, VLAN isolation, and PD Alive watchdog to auto-reboot unresponsive devices. The fanless metal housing ensures silent operation, while desktop or rack-mount options make it versatile for businesses, hotels, and surveillance networks.  Key Features 16 × 10/100Mbps PoE Ports for IP cameras and devices Port 1 Hi-PoE 60W, Ports 2–16 support IEEE 802.3af/at (30W each) 180W Total PoE Power Budget 2 × Gigabit RJ45 Uplinks + 1 × Gigabit SFP for flexible expansion 250m Extend Mode for long-distance PoE transmission VLAN Isolation Mode prevents broadcast storms PD Alive Watchdog auto-reboots offline devices Fanless Metal Housing for quiet and reliable operation Plug-and-Play Setup, no configuration required Desktop or Rack-Mount Installation Certified: CE, FCC, RoHS, UKCA, RCM Technical Specifications Technical Specifications — Wi-Tek Wiking WK-PS219GF Brand / Model Wi-Tek Wiking WK-PS219GF SKU WK-PS219GF Downlink Ports 16 × 10/100 Mbps RJ45 PoE Uplink Ports 2 × 10/100/1000 Mbps RJ45, 1 × 1000 Mbps SFP  PoE Standards Port 1: Hi-PoE up to 60 W; Ports 2–16: IEEE 802.3af/at (30 W each) Total PoE Budget 180 W  Switching Capacity 9.2 Gbps  Forwarding Rate 6.84 Mpps MAC Address Table 2K  Buffer / Jumbo Frame 768 Kbit buffer; 2 KB jumbo frame Forwarding Mode Store-and-Forward DIP Switch Modes Default: 100 m standard mode. VLAN: Downlink port isolation; PD Alive watchdog enabled. Extend: Up to 250 m @ 10 Mbps; PD Alive watchdog enabled. Power Input 100–240 V AC, 50/60 Hz  Power Consumption Idle: 10 W; Full load: 190 W Housing / Cooling Metal (iron), fanless Installation Desktop / Rack-mount Dimensions 320 × 207 × 45 mm  Weight 1.61 kg (net); 2.14 kg (package) LED Indicators PWR: System power status PoE: PoE enabled/disabled Link: On = link; Blinking = activity SW: VLAN/Extend/PD Alive mode status PoE Max: On ≥95% usage; Blinking 90–95%; Off <90%  Operating / Storage –10 °C to 50 °C, 10–90% RH; Storage –40 °C to 70 °C, 5–95% RH Surge / ESD Protection ±4 kV CM, ±2 kV DM; ±6 kV contact, ±8 kV air  Certifications CE, FCC, RoHS, UKCA, RCM Package Contents Switch, AC power cord, Quick Installation Guide, Mounting accessories (hooks ×2, screws ×8) More Information WK-PS219GF Datasheet

Read more less

UniFi USW-Flex-2.5G-8-PoE Switch – 8-port 2.5GbE managed switch with 4 PoE+ outputs, silent fanless design, and compact form factor The UniFi USW-Flex-2.5G-8-PoE is a compact and powerful Layer 2 managed switch with eight 2.5 Gigabit Ethernet ports, four of which support 802.3at PoE+. Designed for high-performance networking in modern homes, offices, and smart environments, this switch delivers multi-Gigabit speeds and flexible deployment options in a sleek, fanless design. Key Features: 8 × 2.5GbE RJ45 Ports for ultra-fast LAN connectivity 4 × PoE+ Ports (802.3at) with up to 60W total PoE budget Fanless, Silent Operation perfect for noise-sensitive setups Compact Desktop or Wall Mount Design Managed via UniFi Network Controller Whether you’re powering access points, IP phones, or cameras, the USW-Flex-2.5G-8-PoE brings reliability and efficiency to your UniFi-powered network. Technical Specifications UniFi USW-Flex-2.5G-8-PoE – Technical Specifications Model USW-Flex-2.5G-8-PoE Total Ports 8 × 2.5GbE RJ45 PoE+ Ports 4 × 802.3at PoE+ (up to 30W per port, 60W total budget) Switching Capacity 40 Gbps Power Input 48V DC (via external power adapter) Mounting Options Desktop or Wall-Mount Cooling Fanless (silent operation) Dimensions 148 × 99 × 28 mm (5.83 × 3.9 × 1.1") Management UniFi Network Controller Operating Temperature 0°C to 40°C (32°F to 104°F)

Read more less

Hikvision 8 Port Gigabit Smart POE Switch, 3E1510P-EI, Transmission, Managed, 2 x UpLink, 110W The Hikvision 3E1510P-EI is an 8-port Gigabit Smart PoE switch designed for reliable network transmission and management. It features 8 Gigabit PoE ports with a total power budget of 110W and 2 additional Gigabit RJ45 uplink ports. Supporting 802.1Q VLAN, STP/RSTP loop prevention, and PoE watchdog functionality, it ensures stable operation by detecting and restarting unresponsive cameras. With cable failure detection, up to 300 meters long-range PoE transmission, and 6KV surge protection, this managed switch is ideal for robust and secure surveillance network deployments. Features 8 × Gigabit PoE port,2 × Gigabit RJ45 port Total PoE Power Budget 110W Support 802.1Q VLAN Support PoE watchdog to detect and restart the cameras that do not respond Support STP/RSTP Loop prevention Support cable detection to locate failure Up to 300 m Long Range PoE Transmission 6KV Surge Protection More Information DS-3E1510P-EI Datasheet

Read more less

IP-COM F1118P-16-150W 16FE+2GE/1SFP Unmanaged Switch With 16-Port PoE Features: Compliant with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z, IEEE802.3x and IEEE802.3af/at standards 16*10/100 Mbps Base-TX RJ45 ports for data transmission and power supply 2*10/100/1000 Mbps Base-T RJ45 ports for data transmission 1*1000 Mbps Base-X SFP slot（Combo） 4 K MAC address table and MAC address auto-learning IEEE 802.3x-compliant full-duplex flow control and half-duplex backpressure flow control 7.2 Gbps backplane bandwidth Maximum power consumption of a single port: 30W Maximum power consumption of the switch: 150W 2.75 Mb cache size for smooth video surveillance 4 modes: standard, priority, extend and VLAN Desktop and rack mounting Downloads F1118P-16-150W Datasheet F1118P-16-150W Quick Installation Guide

Read more less

Ubiquiti Pro Max 48, 48-port, Layer 3 Etherlighting Switch, 2.5 GbE, 16 GbE RJ45 Ports, 32 GbE RJ45 , 4 10G SFP+, Throughput 112 Gbps The Ubiquiti Pro Max 48 is a powerful Layer 3 Etherlighting switch with 48 ports, including 16 2.5 GbE and 32 GbE RJ45 ports, and 4 10G SFP+ ports. With a throughput of 112 Gbps, it's ideal for high-performance networks. Manage it easily with UniFi Network 8.0.24 or later. Features A 48-port, Layer 3 Etherlighting™ switch with 2.5 GbE. Etherlighting™ ports that illuminate to indicate port location, speed/link, and native VLAN/network* (16) 2.5 GbE RJ45 ports (32) GbE RJ45 ports (4) 10G SFP+ ports DC power backup ready Managed with UniFi Network 8.0.24 and later*Pair with UniFi Etherlighting Patch Cables for optimal brightness. Technical Specifications Mechanical Dimensions 442 x 325 x 44 mm (17.4 x 12.8 x 1.7") Weight Without mounting brackets: 4.8 kg (10.6 lb)With mounting brackets: 4.9 kg (10.8 lb) Enclosure material SGCC steel Hardware Management interface Ethernet In-Band Networking interface (32) GbE RJ45 ports(16) 1/2.5 GbE RJ45 ports(4) 10G SFP+ ports Total non-blocking throughput 112 Gbps Switching capacity 224 Gbps Power method (1) Universal input, 100—240V AC, 50/60 Hz(1) USP-RPS DC input Power supply AC/DC, internal, 100W Supported voltage range 100—240V AC Max. power consumption 100W LCM display (1) 1.3" touchscreen Button Factory reset Ambient operating temperature -5 to 40° C (23 to 104° F) Ambient operating humidity 10 to 90% noncondensing Certifications CE, FCC, IC Switching Features Layer 2 features IGMP snoopingSTP / RSTP with priorities and port-level disablePort isolationStorm controlVoice VLANPort mirroringLACP port aggregationMulticast / broadcast rate limitingMAC address blockingFlow control802.1X controlJumbo framesProprietary loop protectionDHCP snooping / guardingEgress rate limitLLDP-MEDPort restricted by MACDevice isolation with ACLs Layer 3 features DHCP for locally-managed networksDHCP relayInter-VLAN routing between networks on same switchStatic routing between local networksNetwork isolation with ACLs Etherlighting™ Ethernet LocatingSpeed/linkNative VLAN/network SFP+ LocatingSpeed/linkNative VLAN/network LEDs System Status RPS Status Application Requirements UniFi Network Version 8.0.24 and later Downloads USW-PRO-MAX-48 Installation Guide

Read more less

Hikvision 16 Port Fast Ethernet Smart Managed PoE Switch, DS-3E1318P-EI 16 × 100 Mbps PoE RJ45 ports, 2 × gigabit combos. IEEE 802.3at/af standard for PoE ports. Network topology management, alarm push, network health monitor. 6 KV surge protection for PoE ports. AF/AT camera can reach up to 300 m in extend mode. Downloads DS-3E1318P-EI Datasheet

Read more less

The Switch Flex XG (USW Flex XG) is a fully managed, mult-gigabit, Layer 2 switch with (4) 10GbE RJ45 ports and (1) GbE PoE input. The USW Flex XG sports slim, compact housing and can be mounted on a desktop*. This switch can also be monitored or configured from anywhere with the powerful, intuitive UniFi Network web application and mobile app.Features: (1) GbE, 802.3at PoE+ RJ45 input (4) 10GbE RJ45 ports Compact, slim housing Can be powered with a 5V, 5A USB-C adapter * Fanless Switch, Do not stack other hardware on the USW Flex XG, will affect heat dissipation Downloads Datasheet Installation Guide

Read more less

Managed Layer 3 switch with (12) 2.5G RJ45 ports with PoE+ for WiFi 6 APs, (12) Gigabit RJ45 ports with PoE+, and (2) 10G SFP+ ports for fiber uplinks.Configurable Gigabit Layer 3 switch with auto-sensing 802.3at PoE+. It offers (12) 2.5G RJ45 Ethernet ports, (12) 1G RJ45 Ethernet ports, and (2) 10G SFP+ ports, providing 2.5G PoE links to your WiFi 6 APs and 10G fiber uplinks to your network. Features include a 1.3" touchscreen, single-row RJ45 port layout for easy patch panel cable management, and UniFi SmartPower Redundant Power System* (USP-RPS) support for intelligent protection from internal PSU interruption or failure.Features: (12) 2.5G 802.3af/at PoE+ RJ45 ports (12) 1G 802.3af/at PoE+ RJ45 ports (2) 10G SFP+ ports 400W total PoE capacity 1.3" touchscreen with AR switch management UniFi SmartPower RPS DC input Managed with UniFi Network Application Version: 5.14.12 or higherMechanical Dimensions 442.4 x 43.7 x 325 mm (17.4 x 1.7 x 12.8") Weight Without Mount: 5.11 kg (11.27 lb) With Mount: 5.2 kg (11.46 lb) Enclosure Materials SGCC Steel Mount Material SGCC Steel Hardware Total Non-Blocking Throughput 62 Gbps Switching Capacity 124 Gbps Forwarding Rate 92.25 Mpps Max. Power Consumption 550W Power Method (1) Universal AC input: 100-240VAC, 8.5A Max., 50/60 Hz (1) USP-RPS DC input: 52VDC, 7.7A; 11.5VDC, 8.7A Power Supply AC/DC, Internal, 550W Management Interface Ethernet In-Band Networking Interfaces (12) 10/100/1000 Mbps RJ45 Ethernet (12) 100/1000/2500 Mbps RJ45 Ethernet SFP+ Interfaces (2) 1/10G SFP+ PoE Interfaces (24) PoE+ IEEE 802.3af/at (Pins 1, 2+; 3, 6-) Max. PoE+ Wattage per Port by PSE 34.2W Voltage Range 802.3af Mode 44 to 57V Voltage Range 802.3at Mode 50 to 57V Services SMB Layer 3 PoE Gigabit Ethernet Switch ESD/EMP Protection Air: ± 16 kV, Contact: ± 12 kV Operating Temperature -5 to 40° C (23 to 104° F) Operating Humidity 10 - 95% Noncondensing Certifications CE, FCC, IC

Read more less

Layer 3, PoE switch with (8) 2.5GbE, 802.3at PoE+ RJ45 ports and (2) 10G SFP+ ports.The Switch Enterprise 8 PoE (USW Enterprise 8 PoE) is a fully managed, Layer 3* switch with (8) 2.5GbE, 802.3at PoE+ RJ45 ports and (2) 10G SFP+ ports.The USW Enterprise 8 PoE also features a 1.3" LCM color touchscreen that concisely displays key system and connection insights. This switch can be monitored or configured from anywhere with the powerful, intuitive UniFi Network web application and mobile app.Features: (1) 1.3" LCM color touchscreen with AR switch management (8) 2.5GbE, 802.3at PoE+ RJ45 ports (2) 10G SFP+ ports 120W total PoE supply Wall-mountable (kit included) * Layer 3 switching will become available in a future firmware update. Managed with the UniFi Network application: Version 6.3.51 and later Downloads Datasheet Installation Guide

Read more less