Extender

NDAA Compliant • Inline PoE Distance ExtenderAxis T8129 PoE Extender (5025-281) — Push Ethernet and PoE Past the 100 m Limit Ethernet stops at 100 m. The AXIS T8129 PoE Extender is a pocket-sized inline repeater that fixes that without a switch cabinet, a fibre run, or a local power point. Fit one every 100 m along the Cat5e or Cat6 cable and both data and PoE carry on down the line — depending on the camera and power source, total runs of 200 to 400 m are achievable. It draws its own power from the passing PoE, so no additional power supply is required, and full-rate network throughput is maintained across the whole extended distance. REACH Up to 400 m total POE STANDARDS 802.3af & 802.3at POWER SUPPLY None required PORTS 2 x RJ45, plug-and-play A Repeater That Fits In Your Palm Traditionally a long cable run means dropping in a switch as a repeater — which means a cabinet, a power outlet and another managed device on the network. The T8129 does the same job in a 105 x 40 x 22 mm, 45 g module that hides in a ceiling void or junction box. Both RJ45 ports self-configure for link speed, duplex and crossover, so there is nothing to set up: cut the cable in, plug both ends in, and the camera at the far end powers up from the same PoE switch or midspan that was already feeding the run. LEDs built into the RJ45 connectors show PoE enabled (green) and link/activity (yellow) for quick fault-finding. No Local Power Needed The extender is fed by the passing PoE and forwards inline power to the device downstream. No power point, no injector, no separate supply at the mid-point. Full-Rate Throughput 10/100 Mbps half or full duplex is maintained across the entire extended distance — the extender does not throttle the link. Chain Them for Distance Add one extender per additional 100 m. A 5 W fixed camera can sit up to 400 m from the switch using three units; a 25 W PTZ can typically reach 200 m using one. Works Across the Axis Range Compatible with all Axis network video products with PoE, supporting both IEEE 802.3af and IEEE 802.3at power sources. Maximum Distance From the Switch Axis publishes the following maximum distances, measured over 24 AWG or heavier Cat5e/Cat6 cable, with one extender added every 100 m. Actual results depend on operating conditions. RANGE BY POWERED DEVICE AND POE SOURCE Powered device PoE switch or Axis 15 W midspan (802.3af) / PoE+ switch (802.3at) / Axis 30 W midspan / Axis 60 W midspan Low power (PoE Class 1, under 6 W) 300 m / 400 m / 400 m / 400 m Medium power (Class 1 or 2, under 12 W) 200 m / 200 m / 300 m / 300 m Full power PoE or PoE+ (over 12 W) Not supported / Not supported / 200 m* / 200 m* Custom High PoE (Axis 60 W injectors) Not supported / Not supported / Not supported / 200 m* * Note Use 23 AWG or heavier cable, typically Cat6 Technical Specifications NETWORK & POWER Data rate 10/100 Mbps half/full duplex Ports Two female Ethernet ports, auto-configured for link speed, duplex and crossover PoE standards IEEE 802.3af and IEEE 802.3at Powering method Powered by the incoming PoE line; no additional power supply required Installation Plug-and-play; automatically forwards inline power to PoE and High PoE-enabled devices Distance Extends beyond the 100 m Ethernet limit; total connection typically 200–400 m depending on midspan and camera type Connectors Shielded RJ45, EIA 568A and 568B Network cables Shielded category 5 or higher INDICATORS & ENVIRONMENT Indicators LEDs on the RJ45 connector — power/PoE enabled (green), link/activity (yellow) Environment Indoor Mounting Wall or shelf Operating conditions -10 °C to 50 °C (14 °F to 122 °F), humidity max 85% RH (non-condensing) Storage conditions -40 °C to 74 °C (-40 °F to 165 °F) Dimensions 105 x 40 x 22 mm (4.1 x 1.6 x 0.9 in) Weight 45 g (1.6 oz) APPROVALS & PART NUMBER Part number 5025-281 Compliance IEEE 802.3af, IEEE 802.3at, RoHS, WEEE, CE Approvals EN 55022 Class B, EN 55024, FCC Part 15 Subpart B Class B with FTP cabling Trade compliance NDAA Section 889 and TAA compliant (Axis Communications, Sweden) Warranty 3-year Axis warranty Downloads Axis T8129 DatasheetAxis PoE Extender Installation Guide Frequently Asked Questions How far can the T8129 extend a cable run?Each extender adds another 100 m. In practice total runs of 200 to 400 m are achievable depending on the powered device and the PoE source — a low-power camera under 6 W on a PoE+ switch can reach 400 m using three extenders. Does it need its own power supply?No. The extender is powered by the PoE passing through it and forwards inline power to the device downstream. That is the main reason it suits mid-span locations with no power outlet. Which PoE standards does it support?IEEE 802.3af and IEEE 802.3at. Axis also lists it as compatible with High PoE 60 W sources for certain device classes — check the range table above, as High PoE devices are only supported from a 60 W midspan and at up to 200 m. How many ports does it have?Two shielded RJ45 ports. Both configure themselves automatically for link speed, duplex and crossover, so there is no in/out orientation to worry about and nothing to configure. What data rate does it support?10/100 Mbps, half or full duplex, and full-rate throughput is maintained over the whole extended distance. It is not a Gigabit device. Can I install it outdoors?No. The T8129 is rated for indoor use only and has no IP rating. For outdoor mid-span locations, Axis offers the T8129-E Outdoor PoE Extender instead. What cable should I use?Shielded category 5 or higher. For the longest published distances, use 24 AWG or heavier Cat5e/Cat6, and for full-power PoE/PoE+ devices at 200 m use 23 AWG or heavier — typically Cat6. Can I chain multiple extenders?Yes. Fit one every 100 m of cable. Up to three units are commonly used to reach 400 m with a low-power camera; higher-draw devices reduce the achievable distance. Will it work with cameras from other brands?It is designed for and tested with Axis network video products, but it operates as a standard 802.3af/at inline extender. Verify the powered device's class and wattage against the range table before ordering. Genuine Axis Warranty Fast AU-Wide Shipping AU Tech Support

Read more less

Genuine Dahua · PoE Extender · 300m ReachDahua PFT1300Extend PoE Power and Data Right to Your Cameras The Dahua DH-AC-PFT1300 PoE Extender uses passive PoE cascade technology to push both power and Ethernet data further than a standard run. Paired with a PFT1200 High PoE Midspan, it can cascade two levels to connect up to 3 IP cameras over a maximum transmission distance of 300m — ideal for long-distance and hard-to-reach installs. 3-Year AU Warranty Fast AU-Wide Shipping AU Tech Support Why You'll Love It 300m Transmission — extends power and data well beyond the standard 100m Ethernet limit. Cascade Up to 3 Cameras — cascade two levels with a PFT1200 midspan to power up to 3 IP cameras (total ≤ 25W). Standards Compliant — supports IEEE 802.3af/at standard power supply for IP cameras. Flexible Mounting — fits inside a junction box or onto a DIN rail for clean, discreet installs. Specifications Model DH-AC-PFT1300 Category PoE & Power Ports 3 x RJ45 10/100M (1 PoE input, 1 to IP cam, 1 to next extender) PoE Standard IEEE 802.3af/at Power Total power consumption ≤ 25W (up to 3 IPC) Transmission Distance Up to 300m Mounting Junction box internal mounting / DIN rail Warranty 3 Years (AU) Frequently Asked Questions How many cameras can it power?Cascading two levels with a PFT1200 midspan lets you connect up to 3 IP cameras, provided total power consumption stays at or below 25W. What is the maximum distance?The extender supports a maximum transmission distance of up to 300m for power and Ethernet data. Is this a genuine Dahua accessory?Yes, this is a genuine Dahua DH-AC-PFT1300 PoE extender backed by a 3-year Australian warranty. How is it installed?It can be mounted inside a junction box or onto a DIN rail, with one RJ45 for PoE input, one for the IP camera and one to feed the next extender.

Read more less

Genuine Dahua · Hi-PoE Midspan · 60W High PowerDahua PFT1200Power High-Consumption Speed Domes With Confidence The Dahua Hi-PoE Midspan DH-AC-PFT1200 delivers Hi-PoE power for high power-consumption speed domes rated up to 60W. Clear status indicators confirm power and PoE supply at a glance, and it works alongside the PFT1300 PoE Extender to cascade two levels and reach up to three IP cameras. 3-Year AU Warranty Fast AU-Wide Shipping AU Tech Support Why You'll Love It Hi-PoE 60W Output — supplies PoE to high power-consumption speed domes drawing up to 60W. Cascadable Power — pairs with the PFT1300 PoE Extender to cascade two levels and power up to three IP cameras. Clear Status Indicators — dedicated LEDs show power (normal power on) and PoE (normal power supply) at a glance. Simple Wall Mount — wall-mount installation keeps the midspan tidy and out of the way. Specifications Model DH-AC-PFT1200 Category PoE & Power Mounting Wall Mount Warranty 3 Years (AU) Frequently Asked Questions What cameras does this midspan power?It is designed for Hi-PoE high power-consumption speed domes drawing up to 60W, ideal for Dahua PTZ cameras. Can I extend the power run further?Yes. Used with the PFT1300 PoE Extender it can cascade two levels of extension and power up to three IP cameras. Is this a genuine Dahua product?Yes, this is a genuine Dahua DH-AC-PFT1200 Hi-PoE Midspan backed by a 3-year Australian warranty. How do I know it is working?Two indicators confirm operation: the power LED shows normal power on, and the PoE LED shows normal power supply.

Read more less

Genuine Dahua · HDMI Extender · 50m Over CAT6Dahua PFM700-ESend HDMI Up To 50 Metres Over A Single Cable The Dahua HDMI Extender DH-PFM700-E transmits HDMI video signals up to 50 metres over a single CAT6 cable with no delay and strong anti-interference performance. Built for HDMI 1.3 compatibility, it supports local loop output, EDID management and one-way infrared remote control. With no drivers or network setup required, it is a plug-and-play solution for professional installations. 3-Year AU Warranty Fast AU-Wide Shipping AU Tech Support Why You'll Love It 50m Over CAT6 — real-time HDMI transmission up to 50m (164ft) using a single pure-copper CAT6 cable, with no delay. HDMI 1.3 With EDID — carries one channel of HDMI video, supports local loop output and EDID management. Infrared Pass-Through — transmits one-way infrared remote control signal alongside the video. Plug-And-Play Protection — no drivers or network setup, with excellent anti-thunder, anti-static and anti-interference protection. Specifications Model DH-PFM700-E Category AV Adapters & Couplers Transmission Distance Up to 50m (164ft) over CAT6 pure copper cable Interface HDMI 1.3, single UTP (CAT-5E / CAT-6) Power Supply DC5V (transmitter only) Warranty 3 Years (AU) Frequently Asked Questions What cable do I need?A single CAT6 pure-copper cable is recommended (DC impedance under 9.5 ohm per 100m). CAT-5E is also supported for the HDMI signal. How far can it transmit?The extender supports real-time HDMI video transmission up to 50 metres (164ft) with no delay. Is this a genuine Dahua product?Yes, this is a genuine Dahua DH-PFM700-E HDMI Extender backed by a 3-year Australian warranty. Do I need to install drivers or configure a network?No. The extender requires no driver installation and no network configuration, making it easy and convenient to install.

Read more less

Dahua · LR1002-1ET/1EC · Ethernet-over-Coax (ePoC) Kit · 1000m ePoC Extender Kit Dahua LR1002 Single-Port Ethernet-over-Coax (ePoC) Extender Kit The Dahua LR1002-1ET & LR1002-1EC kit transmits IP data and PoE power over existing coaxial cable, reaching up to 1000m at 10Mbps (400m at 100Mbps). It powers Dahua and standard IP PoE cameras, letting you upgrade legacy analog systems to HD IP over old RG59/RG6 runs — no costly recabling. Function Ethernet over Coax Ports 1 × RJ45 + 1 × BNC Max Reach 1000m (10Mbps) PoE Power over coax Setup Plug & play Kit TX + RX pair Reuse Existing Coax Run HD IP cameras over your old RG59/RG6 coax — no need to pull new Cat6 through walls, conduits or underground runs. Up to 1000m Reach Transmits IP up to 1000m at 10Mbps or 400m at 100Mbps over quality coax, far beyond standard Ethernet's 100m limit. Power Over Coax Carries PoE alongside data so you can power the remote IP camera directly through the existing coax line. Plug & Play Pair No software setup — fit the transmitter (ET) at the camera end and the receiver (EC) at the switch/NVR end and you're done. Specifications — LR1002-1ET / LR1002-1EC Model / SKU KIT-DH-LR1002-1ET/LR1002-1EC Function Ethernet over Coax (Transmitter + Receiver kit) Ports 1 × 10/100 Mbps Base-TX (RJ45), 1 × BNC Transmission Distance 100Mbps: 400m | 10Mbps: 1000m Power Consumption < 2W per unit Lightning Protection Common mode 4kV / differential mode 2kV Operating Temperature −30°C to +65°C Warranty (Australia) 3 years · CCTV Guru Australia Downloads & Resources LR1002 ePoC Extender Datasheet Can I run an IP camera over my old analog coax?Yes — that's exactly what this kit does. It converts your existing RG59/RG6 coax into an IP link, so you can deploy modern IP cameras without recabling. How far will it reach?Up to 1000m at 10Mbps, or 400m at 100Mbps. Beyond 400m the bandwidth automatically throttles to 10Mbps for a stable connection. Does it power the camera too?Yes — it carries PoE over the coax, so the remote IP camera is powered through the same line that carries the data. 3-Year AU Warranty Fast AU-Wide Shipping AU Tech Support

Read more less